cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
486
Views
15
Helpful
8
Replies
Beginner

Ipv6 image for 2610

Hi all

Can anyone recommend the correct image to download to enable IPv6 support on a 2610 router as shown below. Also a link to the image would be great.

Thanks in advance for your help, greatly appreciated.

regards

 

 

Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Tue 28-Oct-03 05:07 by kellythw
Image text-base: 0x80008098, data-base: 0x80CA4288

ROM: System Bootstrap, Version 12.2(10r)1, RELEASE SOFTWARE (fc1)

Blackpool uptime is 1 hour, 11 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.123-5.bin"

cisco 2610 (MPC860) processor (revision 0x00) with 45056K/4096K bytes of memory.
Processor board ID JAD063505Y3 (541939013)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Everyone's tags (2)
2 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Advisor

Re: Ipv6 image for 2610

Across all versions, the minimum hardware requirement you will need to meet is 64MB DRAM and 16B flash. This should get at least an 'IP Plus' image working.

 

cheers,
Seb.

VIP Advisor

Re: Ipv6 image for 2610

Avoid buying Cisco RAM for this router. Even if you could find it, it would have an eye watering mark-up.

Looking at the installation guide:

https://www.cisco.com/c/en/us/td/docs/routers/access/2600/hardware/installation/notes/2600mem.html#wp92527

 

You need 3.3v EDO 100-pin DIMMs. There should be some on Ebay.

 

As for the flash, that is a SIMM module. But if you want to upgrade beyound 32MB you need to upgrade the Boot ROM. This may be a step too far :) Check the guide:

https://www.cisco.com/c/en/us/td/docs/routers/access/2600/hardware/installation/notes/2600mem.html#wp93177

 

Good luck!

 

cheers,

Seb.

8 REPLIES 8
VIP Advisor

Re: Ipv6 image for 2610

Hi there,
IPv6 support for the 2610 was introduced in 12.2(T) according to the IOS feature browser:
http://cfn.cloudapps.cisco.com/ITDIT/CFN/jsp/by-feature-technology.jsp

 

...what commands are not working?

 

As for downloading other IOS images, these are no longer available for this platform on the Cisco download site. You should be able to find them via google, but you have no way of verifying the MD5 hash of the iage against the Cisco repo, so tread carefully!

 

cheers,
Seb.

Beginner

Re: Ipv6 image for 2610

Thanks Seb

No Ipv6 commands are working 

 

Router1(config)#ipv6 ?
% Unrecognized command
Router1(config)#int s0/0
Router1(config-if)#ipv6 enable
^
% Invalid input detected at '^' marker.

Router1(config-if)#exit
Router1(config)#ipv6 unicast-routing
^
% Invalid input detected at '^' marker.

Router1(config)#

 

VIP Advisor

Re: Ipv6 image for 2610

Ah looking a bit further into this the image you have is the basic 'IP' image. IPv6 support starts with the 'IP Plus' image. There doesn't seem to be support for IPv6 on the 12.3(5) releases. 12.3(6) does have it, so probably your best bet is to look for the 'Enterprise Basic' image which will be the most feature rich:

c2600-j1s3-mz.123-6.bin

 

cheers,

Seb.

Highlighted
Beginner

Re: Ipv6 image for 2610

Thanks once again Seb

If I upgrade to c2600-j1s3-mz.123-6.bin, from the website http://cfn.cloudapps.cisco.com/ITDIT/CFN/jsp/by-feature-technology.jsp

 

cisco router image.pngCisco Image

 

It would seem that I need 64mb dram and my 2610 is only showing  48mb  -

cisco 2610 (MPC860) processor (revision 0x00) with 45056K/4096K bytes of memory.

So would you agree I also need a memory upgrade or is there another IPv6 image more suitable ?

 

Everyone's tags (2)
VIP Advisor

Re: Ipv6 image for 2610

Across all versions, the minimum hardware requirement you will need to meet is 64MB DRAM and 16B flash. This should get at least an 'IP Plus' image working.

 

cheers,
Seb.

Beginner

Re: Ipv6 image for 2610

Thanks Seb

 

i guessed right. Is there any website you can recommend to purchase this ?

 

Regards

 

VIP Advisor

Re: Ipv6 image for 2610

Avoid buying Cisco RAM for this router. Even if you could find it, it would have an eye watering mark-up.

Looking at the installation guide:

https://www.cisco.com/c/en/us/td/docs/routers/access/2600/hardware/installation/notes/2600mem.html#wp92527

 

You need 3.3v EDO 100-pin DIMMs. There should be some on Ebay.

 

As for the flash, that is a SIMM module. But if you want to upgrade beyound 32MB you need to upgrade the Boot ROM. This may be a step too far :) Check the guide:

https://www.cisco.com/c/en/us/td/docs/routers/access/2600/hardware/installation/notes/2600mem.html#wp93177

 

Good luck!

 

cheers,

Seb.

Beginner

Re: Ipv6 image for 2610

Thanks Seb, thats saved me a heap load of wasted time.

CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards