cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
6153
Views
5
Helpful
6
Replies

Router(boot)#

nytrogeno
Level 1
Level 1

I Have a Router Cisco 1601 R

and didn't have the .bin file

I got the file "c1600-nosy-mz.120-5.T.bin" but direct the problem.

I followed the corresponding passes, like these:

rommon 1 > confreg 0x2101

rommon 2 > reset

Router(boot)>

Router(boot)#copy tftp flash

Source file name? c1600-nosy-mz.120-5.T.bin

Router(boot)#

Router(boot)#configure terminal

Router(boot)(config)#config-register 0x2102

Router(boot)(config)#exit

Router(boot)#

Router(boot)#reload

But upon beginning this appear:

Router(boot)>

Router(boot)>enable

Router(boot)#

That could I make?

Help me please...

2 Accepted Solutions

Accepted Solutions

stomasko
Level 4
Level 4

Not sure if you cut things out above or not. Did you try following the procedure on the link below?

http://www.cisco.com/en/US/products/hw/routers/ps214/products_tech_note09186a0080110ed1.shtml

Steve

View solution in original post

Have you tried loading a different image to see if you get the same error upon bootup?

Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)

bdennis@internetworkexpert.com

View solution in original post

6 Replies 6

stomasko
Level 4
Level 4

Not sure if you cut things out above or not. Did you try following the procedure on the link below?

http://www.cisco.com/en/US/products/hw/routers/ps214/products_tech_note09186a0080110ed1.shtml

Steve

Steve:

Yes, I have followed each one of the passes.

However appear the same. That but could I make?

Will the image be that do load that this with errors?

PD: Sorry, my english, but mi first languaje is spanish. Thank!!!

Well,

I already solve the problem. Load a new image in my router but I with the next command:

rommon 1> confreg 0x142

You must reset or power cycle for new config to take effect

rommon 2> initialize

System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)

Copyright (c) 1999 by cisco Systems, Inc.

C1600 platform with 8192 Kbytes of main memory

program load complete, entry point: 0x4020060, size: 0x165eac

%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.

program load complete, entry point: 0x2005000, size: 0x220a1b

Self decompressing the image : ############################################################################### [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) 1600 Software (C1600-Y-M), Version 12.0(19a), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Mon 11-Feb-02 12:42 by shawnk

Image text-base: 0x02005000, data-base: 0x024604A4

cisco 1601 (68360) processor (revision C) with 6144K/2048K bytes of memory.

Processor board ID 24815270, with hardware revision 00000005

Bridging software.

X.25 software, Version 3.0.0.

1 Ethernet/IEEE 802.3 interface(s)

1 Serial(sync/async) network interface(s)

System/IO memory with parity disabled

8192K bytes of DRAM onboard

System running from RAM

7K bytes of non-volatile configuration memory.

4096K bytes of processor board PCMCIA flash (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no

Press RETURN to get started!

Router(boot)>

Router(boot)>enable

Router(boot)#configure terminal

Router(boot)(config)#interface ethernet 0

Router(boot)(config-if)#ip address 10.77.241.160 255.255.255.0

Router(boot)(config-if)#no shutdown

Router(boot)(config-if)#exit

Router(boot)#copy tftp flash

PCMCIA flash directory:

No files in PCMCIA flash

[0 bytes used, 16777216 available, 16777216 total]

Address or name of remote host [255.255.255.255]? 10.77.233.94

!--- Enter the IP address of the TFTP Server

Source file name? c1600-y-mz.120-19a.bin

And solutions my problem...

Thank for colaboration!!!!!!!!!!!!!!

Nytrogeno

I have noted that then of loading the file sends the following:

program load complete, entry point: 0x2005000, size: 0x381d01

Self decompressing the image : ################################################################################################################################################################# [OK]

*** EXCEPTION ***

exception number = 53

program counter = 0x3cd60210

status register = 0x2700

vbr at time of exception = 0x4000000

monitor: command "boot" aborted due to exception

Router(boot)>

Have you tried loading a different image to see if you get the same error upon bootup?

Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)

bdennis@internetworkexpert.com

a.ford
Level 1
Level 1

Look like you maybe haing the same problem I'm haing.

See my post titleed '[invalid checksum]' dated 6JUN04. Do a show flash and see if you get an 'invalaid checksum' message.

I want to try to reload a different Image but I don't know where to get one for a 4500 router

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: