cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1094
Views
0
Helpful
2
Replies

3560 Encapsulation failed

Hello Everyone :)

I recently got a cisco 3560 from cables and kits, and when I was looking at the port statistics I noticed that I had some Encap Failures. Ill post the info below: Also is this something that i should be worried about or is it normal? Thanks :)

IP statistics:
Rcvd: 214822 total, 79503 local destination
0 format errors, 0 checksum errors, 0 bad hop count
0 unknown protocol, 135319 not a gateway
0 security failures, 0 bad options, 14875 with options
Opts: 0 end, 0 nop, 0 basic security, 0 loose source route
0 timestamp, 0 extended security, 0 record route
0 stream ID, 0 strict source route, 14875 alert, 0 cipso, 0 ump
0 other
Frags: 0 reassembled, 0 timeouts, 0 couldn't reassemble
0 fragmented, 0 couldn't fragment
0 invalid hole
Bcast: 54620 received, 6 sent
Mcast: 0 received, 0 sent
Sent: 29865 generated, 0 forwarded
Drop: 8 encapsulation failed, 0 unresolved, 0 no adjacency
0 no route, 0 unicast RPF, 0 forced drop
0 options denied, 0 source IP address zero

ICMP statistics:
Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 5 unreachable
120 echo, 110 echo reply, 0 mask requests, 0 mask replies, 0 quench
0 parameter, 0 timestamp, 0 info request, 0 other
0 irdp solicitations, 0 irdp advertisements
Sent: 0 redirects, 2 unreachable, 110 echo, 120 echo reply
0 mask requests, 0 mask replies, 0 quench, 0 timestamp
0 info reply, 0 time exceeded, 0 parameter problem
0 irdp solicitations, 0 irdp advertisements

TCP statistics:
Rcvd: 24320 total, 0 checksum errors, 33 no port
Sent: 29189 total

UDP statistics:
Rcvd: 55018 total, 0 checksum errors, 54578 no port
Sent: 448 total, 0 forwarded broadcasts

EIGRP-IPv4 statistics:
Rcvd: 0 total
Sent: 0 total

PIMv2 statistics: Sent/Received
Total: 0/0, 0 checksum errors, 0 format errors
Registers: 0/0 (0 non-rp, 0 non-sm-group), Register Stops: 0/0, Hellos: 0/0
Join/Prunes: 0/0, Asserts: 0/0, grafts: 0/0
Bootstraps: 0/0, Candidate_RP_Advertisements: 0/0
State-Refresh: 0/0

IGMP statistics: Sent/Received
Total: 0/0, Format errors: 0/0, Checksum errors: 0/0
Host Queries: 0/0, Host Reports: 0/0, Host Leaves: 0/0
DVMRP: 0/0, PIM: 0/0

OSPF statistics:
Rcvd: 0 total, 0 checksum errors
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks

Sent: 0 total
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks

ARP statistics:
Rcvd: 8889 requests, 9 replies, 0 reverse, 0 other
Sent: 32 requests, 315 replies (0 proxy), 0 reverse
Drop due to input queue full: 0

1 Accepted Solution

Accepted Solutions

balaji.bandi
Hall of Fame
Hall of Fame

This not an issue, as long as they are not increasing gradually, ( if this is old version of IOS, check the show interface fas 0./0)

 

ip broadcast enabled ? or disabled ?

 

 

encapsulation failed

Usually indicates that the router had no ARP request entry and therefore did not send a datagram.

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

View solution in original post

2 Replies 2

Martin L
VIP
VIP

use debug

balaji.bandi
Hall of Fame
Hall of Fame

This not an issue, as long as they are not increasing gradually, ( if this is old version of IOS, check the show interface fas 0./0)

 

ip broadcast enabled ? or disabled ?

 

 

encapsulation failed

Usually indicates that the router had no ARP request entry and therefore did not send a datagram.

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: