Other Security Subjects

Hello, Netpros. I have Cisco VPN 3005 Concentrator with IOS 4.7 running. I wan to configure Rules under traffic management, as i wan to allow only 4 to 5 ip addresses and wans to deny rest of all the ip address. How to define that under Network List....

Does anyone know a software that converts iptables rules to Pix/ASA rules?I have hundreds of rules, so it may be easier to use some help...tkz,Fabio

I need to have multiple ip addresses on a FWSM interface that is presented to the vlan. Is this a possible and if yes how can I accomplish this. Thank youD

I currently have a Cisco ASA 5510 that I am allowing pptp connections from MS vpn clients to our MS remote access server that is behind the ASA. It seems that only 5 users at at time can connect to the network from the Internet through the ASA. Wha...

Greetings.I'm using a 3620 running 12.3.16a IP-FW-IDS 3DES code as a IPSec server for a single client, not site to site. The conneciton uses 10 dot addresses inside of a NAT. It uses a pool for the moment likeip local pool ipsec-51 10.200.51.100 10.2...

The CNS Documentation suggested that " Do not create a Windows domain that equates to a DNS zone (such as example.com). Instead, create a subdomain, such as local.w2k.example.com " in the following page http://www.cisco.com/en/US/products/sw/netmgtsw...

I followed the Cisco instruction to setup webvpn On an ASA 5510 and tested it. I can access our web site. If I type the 192.168.0.230/tsweb. The Remote Desktop Web Connection displays, but I can't access TSWeb. The message is Problems with this Web p...

Today, we have a Web server sitting on a DMZ allowing only 80 and 443 from the outside world. This Web server is not allowed to initiate traffic from the dmz to the outside world. Is there any risk in allowing port 80 traffic to the outside world fro...

HiWe have port security configured in a Cat 6. We used 'restrict' as the viloation method.however some of the ports are still error disabled. example below:interface FastEthernet10/18 description 2-6.7/DR26S02 switchport switchport access vlan 103 sw...

I'm able to establish the tunnel sesion w/o a problem, however in the vpn client log, I keep getting this error message "AddRoute failed to add a route: code 87". Does that mean that it's the vpn client issue or the vpn concentrator configuration iss...

3|Jul 27 2006 07:20:06|106011: Deny inbound (No xlate) tcp src Win:10.161.0.113/2671 dst Win:10.161.155.230/445 What could the possible cause for getting a flood of the above log on ASDM.Would it be a false alarm..

I wanted to put a PIX515 with 7.21 code in transparent mode outside my home office router to supply my MARS box with some traffic to monitor.My home office router, a linksys/vonage rt31p2 gets a single DHCP address from my broadband provider. I do no...

I installed new 525s with FoS7.0.4 to replace my two 515s with FoS6.3. However, the 525s wont pass traffic or reply to inside devices when pinged/etc. I verified that the configs are identical (as much as possible with the syntax changes). The primar...

Hi all, I hope someone can help me. I'm totally new to the PIX and I cant seem to get my inside network to see my web servers on my DMZ. I've attached my config file. Any advice would be a great help!

I have a 2621 configured with the serial interface to the outside world, ethernet 0/0 to DMZ2, ethernet 0/1 to DMZ1, and using ios firewall. When I am connected to DMZ2 I can make FTP communications to the outside world uploading and downloading. W...