Initially, we had CSAMC 4.0 and now we have upgraded to CSAMC 5.0As the User Guide states, the Agents Upgrade should be scheduled from the old CSAMC. For many reasons, I prefer to attempt the upgrade from the new CSAMC. Is that "directly" possible or...
How can I manage an ASA5500 device remotely through VPN. If I use a vpn concentrator and then vpn in, I can manage the vpn concentrator via the public address. Doesn't seem to work for asa devices
hi.can anyone tell me what type of equipment will be "ideal" for completing/passing the CCSP tests?--thanx in advance.---joseph
I'm asked to build a l2l tunnel with a sonicwall TZ170 which has a dynamic public address, providing that this device cannot behave like an easy vpn client, is there a way to tell the vpn3000 to accept a fqdn as a vpn peer or to configure a 0.0.0.0 a...
How do I get the fwsm or pix to reply with it's ttl? Ex. Linux server traces to any other network, default route on server is FWSM interface. That IP does not reply. I am having the same issue on my PIX devices. Can I turn this feature that hides ...
Greetings, I am using a PIX and having a spam problem. We are using the spam service Postini. I want to deny all SMTP traffic unless it comes from one of the Postini servers. A simple task?
HiI am facing a piqular problem.I have 3-4 pix .From inside 3 pix users can ping. but same configure from one pix can not pix.pix inside 192.168.31.10pix outside 192.168.50.227/29router inside 192.168.50.228/29router outside 192.168.100.3-------acces...
Hi everybody,I’m running Cisco ASA software version 7.1(2) on ASA5520 platform. I got a problem when was opening WebVPN login page. The real-time log viewer displayed as the attached file.In addition I’ve tried following the document 65436 at http://...
For interfaces configured as same security level, and global command "same-security-traffic permit inter-interface ".The traffic will flow between interfaces without require any NAT command. And by default traffic flow freely without access-list.If I...
We have enebaled telnet access on a security context and recive a telnet connection but no prompt. Is there anything special you need to do on a context to get telent working on a context. The device I am using to telnet from is a device within the s...
Has anyone tackled error messages when recieving events from Snort 2.3.3? MARS says Unknown Device Event Type for everything so far. Drill down on the raw shows semi important things like an nmap probe or a port scan but MARS template doesnt seem t...
I was wondering what the best practice is for accessing remote routers or switches over the Internet. I don't think locking telnet access to a specific IP via ACL is the best practice and was wondering if SSH is any better. Typically I would have a ...
Hi all, I have a slight problem, any assistance is appreciated. I have a dsl connection coming into a cisco adsl router which does NAT (10.10.10.0), from the router the connection then goes into the a PIX 506e which also does NAT(192.168.1.0).I'v...
Hi,I have installed SW 3.1.1 on my FWSM. The documentation says that ADSM 5.0F is included in 3.1.1. (http://www.cisco.com/en/US/partner/products/hw/modules/ps2706/products_data_sheet0900aecd803ded77.html).Because I couldn't find/activate ADSM 5.0F I...
Hi there all,I am about to roll out some new 7206 DMVPN headend routers and wanted to know if anyone has any experience with stable IOS versions for this.We have used 12.3(6a) until now, but I would like to move to the 12.4-train if possible. Haseeb ...