hi;i have a pix firewall and i want to configure it so as when there is an attack to notify me , how can do that?thanks
hi;i have a pix firewall and i want to configure it so as when there is an attack to notify me , how can do that?thanks
The internal network has a WWW server and a FTP server that users on the Internet can access. All other access to hosts on the internal network is denied from the outside users:I did the similar setup on FTP and WWW, outside users can access FTP but ...
I have been searching MIBs until I am blue in the face. Does anyone know the OID for memory utilization on a Cisco 3000 series concentrator?
Is it possible to block outgoing packets sourced by the router itself?ACLs filter only transit packets. We use 12.2T IOS, thus CPP can't be used.Any suggestions?Vadim
Hi,Does FWSM v 2.3.1 support Stub Multicast Routing Feature ?I've found this FAQ which explain that this feature is supported : http://www.cisco.com/warp/public/707/fwsm-faq.htmlBut I didn't find any documentation how to configure it on a FWSM.I trie...
I want to know how I can syncronize the clock on the 3002 client with a 3015 concentrator.Mark
I am trying to configure a site to site with a cisco 831 (easy vpn) and a cisco 3030 and I can't seem to find documentation on how to do that. Does anyone know where I can find this info?Thanks!
I am trying to permit just a handful of ports on several routers. What is the correct syntax to do this? and, if there is a good document that I can reference on a regular basis... what is that.Thanks...Phil
I have a simple question. What is normal usage for the memory? I got my Pix 501 memory usage like this:Used: 10.927 (MB)Free: 5.073Totoal: 16I am just doing very simple NAT/PAT and some port forwading, is this usage normal or not? If not, how to refr...
Hi,i have a PIX 515 with 4FE and i have inside/DMZ/outside1/outside2.I want that a machine in DMZ that send/receive mail from one ISP(outside1) and i want that the same machine and other from internal network goes browsing (HTTP/HTTPS/FTP etc) throug...
We want to give our desktop team the ability to change the speed and duplex, shut and no shut for the fast Ethernet interfaces on our closet switches. I can, by using priviledge command achivew this, but it doesn't seem I can limit it to just the Fa...
Ok, here is the situation. My PIX 525E seems to be working properly for the most part. When I send an email from an internal machine, which is on the subnet of the inside interface, it correctly goes out. However, when I look at an email at its de...
I've set up a single firewall with 1 B class network, with 4 subnets on the inside and 1 C class network in the DMZ.They are connected to an external network. Have initiated DHCPRelay in C class interface, with helper address and DHCP Server in B cl...
Hi,I am having some servers in our DMZ area. Pix 535 are having three access list as belowin_outside_toughin_inside_basicin_dmzI want to access my servers from inside our netowrk to the dmz area. I can access from dmz to inside of our network but not...
Hi ,Was wondering if someone could assist in clarifying a NAT issue on the PIX.I have an existing dynamic NAT rule configured that nats my entire 10.0.0.0 network range to my outside interface address. I now have a required where outside access is re...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-05-2024 11:31 AM | ||
03-26-2024 01:41 AM | ||
03-14-2024 11:57 PM | ||
02-28-2024 12:11 PM | ||
02-27-2024 07:31 AM |