Other Security Subjects

Hey all,I have had a pix 515E prevent traffic outbound twice in the last 18 hours. Once I restart the firewall, all is well again. The pix is running 6.3.3 OS.My question is geared more towards trying to figure out why it is doing so. What would be s...

Currently im testing fail over between two 3000series concentrators in our lab. I have succesfully been able VPN to either concentrators seperatly but cant VPN using the Clustered address. Here is my setup3015 concentrator3060 concentratorSBC Static ...

hi:all i am preparing a project for our coming FWSM,but i dont know how to modify our present network struture to adpat fwsm.Now i have two 6500,many vlans,and ospf is run.i think 4-5 DMZ in future is needed ,but between the DMZs how to route,is the...

After installing a 4 port 10/100 adapter to a 4235. During the boot process the system hangs requesting F1 to continue or F2 to enter setup. After pressing F1 the system boots and operates fine. Any ideas why the pause after the reboot? I am worried ...

Hi,Any idea how to simulate network attacks eg syn flood or DDOS etc?ThanksSteven

Does anyone know what access-list I need to give servers on my dmz access to the internet via the outside interface but no access to my internal LAN?Below is parts of my config. If you need more info, let me know.nameif ethernet0 outside security0 ...

i have a pix 501 ver 6.3 pdm 3.i want to apply a dns doctoring alias command so internal users will access my internal web site with his public dns name=public ipi did : alias (inside) 192.168.1.2 10.10.10.10 255.255.255.255 when 10.10.10.10 is the p...

I have an application class (anti-virus in this case) configured as an exception to the trojan detection policy, however it's not working. No matter what application class I exclude, it seems to be ignored. Seems to be a bug.

Currently we have Spoke and HUB VPN tunnels configured manually for about 100 sites. We are evaluating DMVPN to simplify and enable Spoke to Spoke tunnels. As for DMVPN, spokes initialize tunnels and register to the HUB router for Next hop router. Ou...

After a few hours of the sensor running the AnalysisEngine dies. Why does this happen?Application Partition:Cisco Systems Intrusion Detection Sensor, Version 4.1(3)S87OS Version 2.4.18-5smpbigphysPlatform: IDS-4250-SXSensor up-time is 2:57.Using 5586...

I am going to use IDS.but when I boot the system I am getting problem.Please have a look.ed Hat nash version 3.3.10 starSCSI subsystem driver Revision: 1.00tingLoading sckmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2si_mod modu...

I tried to update this signature on my VMS, but it hangs, won't allow me to finish. Please advice!

I get an error pasting in the access-list stating that the memory has exhausted. When I issue the command to see my lists, it only shows one of them. I try and paste in the other and I get the same message. I did notice a note to save to flash but ca...

Hi guys: I have few basic questions regarding IDS.Hope someone can give help me out. 1.Does any version of IDS have SNMP Support. 2.Is there any major difference in configuring 4230 and others like 4235 ,..latest ones ?Thanks a lot

Hello together,maybe you can help me!Installation VMS 2.2, VMS 2.2 Update 1, MC_IDS 1.2.3,all IDS_xxxx processes are running.I want to get an E-Mail if signatures are matching the severity level high, using the Perl script "emailalert.pl"!The events ...