cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
1877
Views
0
Helpful
5
Replies
robbhanMid
Beginner

No translation group found

Hi,

I get the following error message when I try to connect over a site-to-site VPN:

No translation group found for tcp src outside:10.10.10.2/1038 dst inside:192.168.1.22/80

How do I set up the asa so that all traffic coming from 10.10.10.2 gets properly translated and can travel the inside hosts on 192.168.1.0?

thanx

My config:

interface Vlan1

nameif inside

security-level 100

ip address 192.168.1.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

ip address 10.10.10.1 255.0.0.0

!

interface Vlan3

nameif dmz

security-level 50

ip address 192.168.200.1 255.255.255.0

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

switchport access vlan 3

!

interface Ethernet0/6

!

interface Ethernet0/7

!

passwd xxx

ftp mode passive

dns server-group DefaultDNS

domain-name *

access-list http_access_in extended permit tcp any any eq www

access-list dmz_access_in extended permit icmp 192.168.200.0 255.255.255.0 192.168.1.0 255.255.255.0

access-list dmz_access_in remark Specify what kind of trafic should be allowed to travle to the inside network

access-list dmz_access_in extended permit tcp host 192.168.200.2 192.168.1.0 255.255.255.0 eq www

access-list NO-NAT extended permit ip any 192.168.200.0 255.255.255.0

access-list ftp_access_in extended permit tcp any any eq ftp

access-list 8080_access_in remark Specify what kind of trafic should be allowed in. Don't forget the NAT

access-list 8080_access_in extended permit tcp any any eq www

access-list l2l_list extended permit ip 192.168.1.0 255.255.255.0 192.168.100.0 255.255.255.0

pager lines 24

logging enable

logging asdm informational

mtu inside 1500

mtu outside 1500

mtu dmz 1500

no failover

icmp unreachable rate-limit 1 burst-size 1

asdm image disk0:/asdm-603.bin

no asdm history enable

arp timeout 14400

global (outside) 1 interface

nat (inside) 0 access-list NO-NAT

nat (inside) 1 0.0.0.0 0.0.0.0

nat (dmz) 1 0.0.0.0 0.0.0.0

static (dmz,outside) tcp interface ftp 192.168.200.2 ftp netmask 255.255.255.255

static (dmz,outside) tcp interface 8080 192.168.200.2 8080 netmask 255.255.255.255

static (dmz,outside) tcp interface www 192.168.200.2 www netmask 255.255.255.255

access-group 8080_access_in in interface outside

access-group dmz_access_in in interface dmz

route outside 192.168.100.0 255.255.255.0 10.10.10.2 1

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout uauth 0:05:00 absolute

dynamic-access-policy-record DfltAccessPolicy

http server enable

http 192.168.1.0 255.255.255.0 inside

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart

crypto ipsec transform-set FirstSet esp-3des esp-md5-hmac

crypto map abcmap 1 match address l2l_list

crypto map abcmap 1 set peer 10.10.10.2

crypto map abcmap 1 set transform-set FirstSet

crypto map abcmap interface outside

crypto isakmp enable outside

crypto isakmp policy 1

authentication pre-share

encryption 3des

hash sha

group 2

lifetime 43200

no crypto isakmp nat-traversal

telnet timeout 5

ssh timeout 5

console timeout 0

dhcpd auto_config outside

!

dhcpd address 192.168.1.20-192.168.1.99 inside

dhcpd enable inside

!

threat-detection basic-threat

threat-detection statistics access-list

tunnel-group 10.10.10.2 type ipsec-l2l

tunnel-group 10.10.10.2 ipsec-attributes

pre-shared-key *

!

class-map inspection_default

match default-inspection-traffic

!

!

policy-map type inspect dns preset_dns_map

parameters

message-length maximum 512

policy-map global_policy

1 ACCEPTED SOLUTION

Accepted Solutions

ASA1

access-list NO-NAT extended permit ip 192.168.1.0 255.255.255.0 192.168.200.0 255.255.255.0

nat (inside) 0 access-list NO-NAT

ASA2

access-list NO-NAT extended permit ip 192.168.200.0 255.255.255.0 192.168.1.0 255.255.255.0

nat (inside) 0 access-list NO-NAT

View solution in original post

5 REPLIES 5
a.alekseev
Rising star

What is 10.10.10.2?

Oh! maybe I wasn't clear enough.

10.10.10.2 is the outside interface of the other asa whos computers on its inside network needs to communicate with inside clients on this asa.

check "nat (inside) 0" on another ASA.

I have nat (inside) 1 0.0.0.0 0.0.0.0

on both my asa's. Is this correct?

ASA1

access-list NO-NAT extended permit ip 192.168.1.0 255.255.255.0 192.168.200.0 255.255.255.0

nat (inside) 0 access-list NO-NAT

ASA2

access-list NO-NAT extended permit ip 192.168.200.0 255.255.255.0 192.168.1.0 255.255.255.0

nat (inside) 0 access-list NO-NAT

View solution in original post

Content for Community-Ad

This widget could not be displayed.