Does SRv4 support setting color values for BGP vpnv4 neighbor outbound directions？My experimental results indicate that color values can only be set in the receiving directionHow to do that?
Hi All,Need a small help here.My customer currently doesn`t use Cisco Service Provider products much in its architecture.Hence, I was preparing for SPCOR exam earlier but then stopped after looking their existing and new service provider architecture...
Hi, i have a setup which consists of XR and XE routers. is flex-algo supported for IPv6 in IOS-XE?
I have configured Flex-algo 128 in all the routers.. I could not see the topology for flex-algo 128 in XE routers and XR routers are fine... When doin...
Hi All,
we are running CV 4.1.3 and have a few sensors connected and ingesting data in CV.. working well sofar.
However i have some questions that i cannot find on the admin guides or cisco.. hope someone here can assist.
Q1 – Vulnerability updates –...
What is the equivalent of "next-hop-self all" command in IOS-XE for the IOS XR. This command allows the changing of next hop even when the routes are being learnt from an ibgp neighbor and are shared with another ibgp neighbor. For IOS XR, I am unabl...
Hello all I have the following config on PE1:vrf definition C1-BCRrd 188.62.59.1:100route-target export 8707:200route-target import 8707:300!address-family ipv4exit-address-familyvrf definition C2-FCArd 178.172.253.30:1route-target export 8707:200rou...
Hi everyone,A customer is using a stormshield FW as a CE to access internet via our service provider infrastructure on PPPoE session.The PPPoE session is UP on our ASR1009-X Access router on a virtual-access interface. The policy map is limiting the ...
I've been a CCIE for over 20 years and have connected a few dozen companies redundantly via BGP to the Internet over that time. It's been about 5 years since the last time I brought up redundant BGP routed ISP connections, and maybe I didn't do as m...
Hello Cisco Community,I upgraded about 10x A901-6CZ-F-A but got an error on one of the units. Error: Licensing infrastructure is NOT initialized.upgraded to asr901-universalk9-mz.156-2.SP9.bin units boots up fine, but then i get the error and I'm not...
Hello all,I'm trying to do a lab in gns3 where I have some routers one is CE4 and one is PE2,I want to advertise the loopback 11 of PE2 to CE4 that resides on vrf C1 and is not working. I paste here the config on PE2 and CE4 maybe I did something wro...
Hello facing an issue in upload and download in BGP load sharing scenario My upload is goes to one isp and download goes to second isp. I want that upload and download should goes to same isp103.216.135.0/24 upload and download to isp1 (inbound outb...
Hello Guys,I need to replace Cisco 7206VXR (NPE-G1) with PA-MC-STM-1SMI adapter. Since it is very old hardware I am having hard times finding a decent replacement. What would you sugest please? It does now have to be new nor under support.Thanks,
I am installing EPNM 5.0 in VMWare environment following the steps from config guide(Evaluation License). After successful installation I could able to login to GUI with admin credentials but not able to login to CLI. Verified that the Administrator ...
Hi Guys,I am looking for some info regarding the usage PI and PA addresses.What are the use-cases?When would it be advisable to use one?How does it affect BGP?Do ISP clients still need to be on a different AS if they have a PA address?Appreciate some...
After a reboot of the server hosting our CSMS installation the application is now failing to start.
The systemd service csm-supervisor.service, which in turn attempts to start a docker container, is attempting to fetch components from Cisco's docker ...
