Other Service Provider Subjects

When we provision a subscriber to an SCE package with rules to redirect HTTP flows, then this redirection is not available right away, but only after about 10 seconds have passed. Before the redirection gets enabled, the HTTP requests just get blocke...

Hi all,  I am configuring a 2801 router . I set up ip address on the interface Fa 0/0 and  'no shutdown' command. But, after a restart , the interface is changing to down  again!  What I must do to ? Thanks in advanced!

Hi to All,Just want to know how we can verify that the  Jumbograms (RFC2675) is supported on the router running IPv6. Is there a CLI show command to verify the support for this feature / RFC or do we still need to activate it.Your immediate response ...

Please I need help from someone who has ever wondered and get to know the maximum number of simultaneous IP sessions on 7600. On the documentation, this is the applicable information that we find regarding the number of sessions:http://www9.cisco.com...

Hi.When we do the upgrade version of SCE8000 from version 3.5.5 to 3.6.5 the SCE8000 restart with version 3.5.5. We did the upgrade by console CLI and SCA BB, without success.Regards.

Hello,I did SCE8000 upgrade over GUI but upgrade process failed. Below is log from GUI.!- GUI log!+ 4/21/11 12:51:11 AM CEST | INFO  | Opening FTP daemon on port 21+ 4/21/11 12:51:11 AM CEST | INFO  | Updating OS at "SCE-01-BA2 (MSC7) [10.19.7.27]": ...

Good morning I'm having problems configuring out of band clocking between two MWR-2941I have configured one MWR-2941 toRemoterecovered-clock slave!interface Virtual-Cem 0/24cem 0     xconnect 10.10.10.2 7600 encapsulation mplsnetwork-clock select 1 P...

Hello,  I am needing to set up a 2801 router as a bandwidth controller. My intention is only bandwidth control over IP address, no specific traffic. Until now I had some success but I'd like to know what is the  better way to do that. Thats my confi...

Hi all,I would like someone to help me regarding the following issue that I have found trying to configure Etherchannel+dot1q in a b2b connection from an ES20+ port to a LAN SW board.We have a 7600 with c7600rsp72043-advipservicesk9-mz.122-33.SRE3.sh...

As usual, on Earth Day we all think a bit more about the environment and our role in helping to protect the natural world around us.  Because we are all technologists of some sort here in the Community, I wanted to pose this question today: does tech...

I'm looking at the most scalable alternative for an LNS for a small/mid-size ISP.I have looked at Cisco 10K, ASR 1000, maybe a 7600 and it's difficult to compare the price/features/road-map.Any recommendation?Is there a Cisco white paper comparing th...

Hello,I am working on a design wherein i need some inputs in terms of the number of PPPoE sessions that can be terminated on the ISR-G2 devices especially 3945/3945 E routers and also ASR1K routersIf there is any official cisco document on the same i...

Dear allI have a LNS running c7200-adventerprisek9-mz.124-24.T4.bin.I am trying to delegate IPv6 prefixes to vpdn users as described inhttp://www.cisco.com/en/US/customer/prod/collateral/iosswrel/ps6537/ps6553/whitepaper_c11-602131.html#wp9000270From...

Hi everyone,Please let me know if i can user Cisco UBR7200 (NPE-G1) as BRAS. If possible, which IOS required to enable this feature?Thanks in advance.Regards,Nil.