Other Service Provider Subjects

Greeting To All , I want to buy Cisco 881 k9 router but i don't no.is that support dual link from ISP at the same time.suppose primary link goes down backup link get up automatically.can anyone help me please.however that has 1 WAN port and 4 LAN por...

Hello, I would like to know the difference between these two definitions: neighbor 1.1.1.1 remote-as 65015  (configured by single command) and doing it by 2 separate commands which will result in following config neighbor 1.1.1.1   remote-as 6501...

Hi Could you tell me questions below? 1.FEC CapabilitiesCould you tell me when will be FEC capabilities for Media Interface Card provided ?According to DataSheet of Media Interface Card, In future releases it will provide the same functionality as ...

Hi, I found that I cannot do a packet capture on our PPPoE interface, there is no ingress packet captured, only egress packets. I have tried on different interface, still no ingress packet. But there is ingress traffic running on the interface. Anyo...

Dear sir/madam such as CRS-1  for ebgp unequal loadbalance I have a situation customer has 8 crs-3s ebgp connect to other same AS each  crs-3 has 2 100G link, ebgp. uplink to same AS if one link on one CRS-3 is down, the whole bandwidth on this rout...

when one link in etherchannel is down , I know ospf can react to change cost to large value Can ISIS/BGP support this?  if ebgp one link in etherchannel is down , bandwidth of etherchannel decreased.Ebgp can react to this problem

hey please i need to help , i try to install modul EHWIC-D-8ESG-P in router cisco 3925 but this card is not detected . cordialy

Dears, I facing an missing command when I configure IP SLA on Cisco Router 2911 with IOS 15.5(1)T2, I coudn't find the command "IP SLA Number" what the steps to configure IP SLA on this CIsco Model ? Thanks in advanced,

Hello, I would like to know if it was possible (on a PPPoE cisco server) to automatiquely configure the bandwidth of a virtual-access interface when I receive the rate-line of the DSLAM ? I would like this feature in order to apply QoS with policy m...

Hi everybody, Regarding the documentation http://www.cisco.com/c/en/us/td/docs/switches/metro/me3600x_3800x/software/release/15-2_4_S/configuration/guide/3800x3600xscg.pdf Table 12-2 there is limitation in 'Maximum Service Instances in the Group' and...

Hello, i search for a way to activate a RTU (License_for_up_to_2M_Sessions) on an asr1006 advanced enterprise. i found some how-to, but in every how-to use "license"-commands. Thats a problem because the asr doens't know any "license"-command. I'm n...

Good afternoon. We have to use the equipment ASR-1004 (boot system bootflash:asr1000rp1-adventerprisek9.03.16.00.S.155-3.S-ext.bin).Use ip unnumbered, QinQ. Integration ISG billing system UTM5 from Netup. It has been observed that NAS-server closing ...

Hi all ,Strange lines apperas in log on Cisco ASR 1004 RP2 ESP20Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.2(2)S, RELEASE SOFTWARE (fc1)asr1000rp2-advipservicesk9.03.06.00.S.152-2.S.binUsing him to terminate...

Dear Gents,I have an ASR 901 router chassis A901-6CZ-F-A.This router has 4 copper and 4 SFP ports are disabled by default which requires FLS-A901-4 to be enabled.When i purchased and installed this license to the router it enabled the 4 copper ports ...

Hello everyone. I'm trying odap on my router for pppoe users. I configured a "peer default ip address dhcp-pool pppoe2 pppoe" on virtual-template interface. All worked well. But when networks in dhcp pool "pppoe" are ended the switching to pool "pppo...