Other Service Provider Subjects

Hello;Extract of the output of the command sh int linecard 0 subscriber name xxx is as follows:P_MibSubCounters16[0..31][0..1]=0*2,2841,32401,0*2,1,0*7,60,616,6,21,3,0*7,18,2789,0*20,18,223,0*4,82,1687,1,6,0*6P_MibSubCounters32[0..31][0..1]=0*2,34354...

Hi,I have installed SCE2020 with version 3.6.5 in between a mikrotik to which users call through pppoe, and another router where the GW for those users is created, then to the internet.When i launch show int linecard 0 subscriber all-names command, i...

Guys!I've got a 4Mbps Internet link over fiber optic from my ISP. I need to upload heavy files to a US based server on daily basis. The latency between source (Pakistan) & destination (US based FTP server) is around 340 msec on avg. On a single file ...

Dear all,I want to ask about Cable broadband, using UBR10012.I have try to use DS Resiliency (Using cable rf-change-trigger command with cable resiliency ds-bonding) in IOS SCG3 version and wideband resiliency in IOS SCC7 version, but i can't find a ...

Cisco 7600 reports in log Jun 22 02:21:38.315: SP: FAILED to write to DS1338 RTC deviceit reports every day can anyone helps what it means ?BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)S...

Hi everyone;i was going through some of the configs on our service provider managed cpe device. policy-map CUSTOMER_POLICY_INclass class-default police cir <EF policing rate in bps>bc <Policing Burst Parameters, in Bytes> conform-action set-dscp-tran...

        Can anyone share the knowledge about how vpls is fuctioning if we have cutomer(eg: cust A) at one site and the customer A has a branch at different geograpgical sitse. How vpls can handle diffrent vlans from a single customer site? Please sha...

Hi All,I've combed through reference and config guides but cannot find documents pertaining to the following command under isis:nsf advertise-holdtimeDoes anyone know exactly what this does?Thanks

HI guys：SPA-2X1GE-V2 module interface can work L2 switchport？same：!interface GigabitEthernet5/1/1 switchport switchport access vlan 20 switchport mode access

HelloI want to use qinq tunnelling in my network. I have 2 cisco 3750 on the edge terminating the qinq tunnels, but in between i have cisco 2960.My question is does cisco 2960 pass qinq trafficThank uSent from Cisco Technical Support iPhone App

HI,Simple quetion we are trying to pull interface usage in mbps or bps from SNMP to a Nexus 5548p.We cant seem to use the normal mib we use for this against IOS devices which is 1.3.6.1.4.1.9.2.2.1.1.8  for Out bits sec and 1.3.6.1.4.1.9.2.2.1.1.6 fo...

Hello,I have two questions regarding ASR 9010 in dual chassis, with dual RSP per chassis, with full redundant connections between.First question is when I had upgrade ASR from 4.3.0. to 4.3.1. version, and activate installation packages:RP/0/RSP0/CPU...

Hi everyone,I just began to deep dive in some brand new ASR 1001.I read about that functionnality and try to play with ... but unfortunatly it doesn't work.- Hardware & Software Info:IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.2(4)S...

I am seeing the below error on a UBR10012.  The card in use is aUBR-MC20X20VSLOT 5/0: May 15 17:10:18: %LICENSE-6-VIOLATION: Feature DS_License 1.0 count violation - count = 20, usage count = 40.SLOT 5/0: May 15 17:11:18: %LICENSE-6-VIOLATION: Featur...