cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1413
Views
0
Helpful
7
Replies

Failed to apply service configuration at SCE2020 : SCA BB Console error

Chaker BCHIR
Beginner
Beginner

Hello,


When I tried to apply the service configuration at the SCE 2020 that I used, I couldn't, and I obtained the following error message :

----------------------------------------------------------------

Failed to apply service configuration at "SCE device 2 MED [10.150.37.130]": connection is not active ### java.lang.IllegalStateException java.lang.IllegalStateException: connection is not active
connection is not active ### java.lang.IllegalStateException java.lang.IllegalStateException: connection is not active

----------------------------------------------------------------

Could you help me please ?


I heard also about a bug when applying this .pqb file , Is it true that I should change the burstsize before I apply the service configuration to eliminate the bug ?



Thanks a lot.

3 ACCEPTED SOLUTIONS

Accepted Solutions

mmiletic
Cisco Employee
Cisco Employee

Hi,

This is maybe because of network connectivity issue. Did you try to put the PC with SCA BB in the same VLAN as your SCE is, and then to try with applying the configuration?

Do you receive the same error?

Also check this doc and system requirements for SCA BB console 3.5.5:

http://www.cisco.com/en/US/docs/cable/serv_exch/serv_control/broadband_app/rel355/scabbug/04_SCA_BB_UG.html#wp1045602

or find appropriate user guide version on http://www.cisco.com/en/US/products/ps6135/products_user_guide_list.html:

Regards,

Minja

View solution in original post

It can also be caused by the operating system version used for the SCA BB Console, see this post:

https://supportforums.cisco.com/message/3220011

SCA BB Console version 3.6.0 is supported only on Windows 2000 or Windows XP:

http://www.cisco.com/en/US/docs/cable/serv_exch/serv_control/broadband_app/rel36x/product_install/Product_IG_QSG.html#wp41684

Cheers,

Tom

View solution in original post

Hi Chaker,

Since Windows 7 is not a supported platform for the SCA BB, we don't have much experience with it (I don't know how bad it is broken).

About the VLAN part of the question, the problem is not that SCE and SCA BB console are on a separate VLAN, this should normally work.  Minja's point was that if there is a network connectivity issue with the current setup, it would probably get bypassed if the SCA BB console and SCE are put on the same VLAN.

On the other hand, could it be that Windows 7's firewall is handling traffic differently when communicating with a different subnet or the same subnet?

Tom

View solution in original post

7 REPLIES 7

Chaker BCHIR
Beginner
Beginner

Any response for this java problem ?

mmiletic
Cisco Employee
Cisco Employee

Hi,

This is maybe because of network connectivity issue. Did you try to put the PC with SCA BB in the same VLAN as your SCE is, and then to try with applying the configuration?

Do you receive the same error?

Also check this doc and system requirements for SCA BB console 3.5.5:

http://www.cisco.com/en/US/docs/cable/serv_exch/serv_control/broadband_app/rel355/scabbug/04_SCA_BB_UG.html#wp1045602

or find appropriate user guide version on http://www.cisco.com/en/US/products/ps6135/products_user_guide_list.html:

Regards,

Minja

Thanks a lot Minja for your response.

I think it is true because I tried to apply the config (.pqb file) from my PC located in the same VLAN as the SCE and I it worked !

Regards.

It can also be caused by the operating system version used for the SCA BB Console, see this post:

https://supportforums.cisco.com/message/3220011

SCA BB Console version 3.6.0 is supported only on Windows 2000 or Windows XP:

http://www.cisco.com/en/US/docs/cable/serv_exch/serv_control/broadband_app/rel36x/product_install/Product_IG_QSG.html#wp41684

Cheers,

Tom

Thanks very much Tom ,


I used Windows 7  in my laptop , so you think that it is caused by the OS version.

I thought also like you for a period, but it worked when I applied it and my PC is on the same VLAN as the SCE.



My friend used Windows XP and he had not any problem !


Problem of VLAN ? Problem of OS ? I am really confused. We have here 2 hypothesis




Best Regards.

Hi Chaker,

Since Windows 7 is not a supported platform for the SCA BB, we don't have much experience with it (I don't know how bad it is broken).

About the VLAN part of the question, the problem is not that SCE and SCA BB console are on a separate VLAN, this should normally work.  Minja's point was that if there is a network connectivity issue with the current setup, it would probably get bypassed if the SCA BB console and SCE are put on the same VLAN.

On the other hand, could it be that Windows 7's firewall is handling traffic differently when communicating with a different subnet or the same subnet?

Tom

Thanks a lot Tom,


Now I am sure that the problem is from Windows 7



I am now in front of 2 explanations :

- Windows 7's firewall is handling traffic differently when communicating with a different subnet or the same subnet as you said.

- Or : last time when I applied configuration when my PC is on the same subnet as the SCE I had my firewall not running (desactivated) , and those days when I was with my clients (not in the same network as the SCE) and I applied config (.pqb file), the firewall was running, I'm sure of this.




Thanks Tom, thanks Minja.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: