cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5940
Views
15
Helpful
10
Replies

3702i won't join controller

Wes Schochet
Level 3
Level 3

Just unboxed my first new 3700 AP.   Fired it up and it doesn't appar to like my controller.  Anyone have any suggestions?

IOS Bootloader - Starting system.

flash is writable

Tide XL MB - 40MB of flash

Xmodem file system is available.

flashfs[0]: 12 files, 2 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 41158656

flashfs[0]: Bytes used: 7354880

flashfs[0]: Bytes available: 33803776

flashfs[0]: flashfs fsck took 10 seconds.

Base Ethernet MAC address: 3c:08:f6:6c:f5:04

Ethernet speed is 1000 Mb - FULL Duplex

Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...##########################

File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000

executing...

Secondary Bootloader - Starting system.

Tide XL MB - 40MB of flash

Xmodem file system is available.

flashfs[0]: 12 files, 2 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 41158656

flashfs[0]: Bytes used: 7354880

flashfs[0]: Bytes available: 33803776

flashfs[0]: flashfs fsck took 10 seconds.

Base Ethernet MAC address: 3c:08:f6:6c:f5:04

Boot CMD: 'boot  flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx;flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx'

Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...######################

File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x1003000

executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C3700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Sat 16-Nov-13 10:46 by prod_rel_team

Tide XL MB - 40MB of flash

Initializing flashfs...

flashfs[2]: 12 files, 2 directories

flashfs[2]: 0 orphaned files, 0 orphaned directories

flashfs[2]: Total bytes: 40900608

flashfs[2]: Bytes used: 7354880

flashfs[2]: Bytes available: 33545728

flashfs[2]: flashfs fsck took 10 seconds.

flashfs[2]: Initialization complete.

flashfs[3]: 0 files, 1 directories

flashfs[3]: 0 orphaned files, 0 orphaned directories

flashfs[3]: Total bytes: 11999232

flashfs[3]: Bytes used: 1024

flashfs[3]: Bytes available: 11998208

flashfs[3]: flashfs fsck took 1 seconds.

flashfs[3]: Initialization complete.

Copying radio files from flash: to ram:

%Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)

%Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)

%Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)

%Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)

%Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)

%Error opening flash:/ap3g2-rcvk9w8-mx/R2.bin (No such file or directory)

%Error opening flash:/ap3g2-rcvk9w8-mx/Q2.bin (No such file or directory)

%Error opening flash:/ap3g2-rcvk9w8-mx/C2.bin (No such file or directory)

Uncompressing radio files...

File not found: flash:/ap3g2-rcvk9w8-mx/8004.img

File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin

File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin

File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin

File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin

File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin

File not found: flash:/ap3g2-rcvk9w8-mx/R5.bin

File not found: flash:/ap3g2-rcvk9w8-mx/Q5.bin

File not found: flash:/ap3g2-rcvk9w8-mx/C5.bin

File not found: flash:/ap3g2-rcvk9w8-mx/8006.img

...done Initializing flashfs.

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

no ip http server

       ^

% Invalid input detected at '^' marker.

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-CAP3702I-A-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.

Processor board ID FTX175071RZ

PowerPC CPU at 800Mhz, revision number 0x2151

Last reset from power-on

LWAPP image version 7.6.1.118

1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 3C:08:F6:6C:F5:04

Part Number                          : 73-15243-01

PCA Assembly Number                  : 000-00000-00

PCA Revision Number                  :

PCB Serial Number                    : FOC17482H3B

Top Assembly Part Number             : 068-05054-01

Top Assembly Serial Number           : FTX175071RZ

Top Revision Number                  : A0

Product/Model Number                 : AIR-CAP3702I-A-K9  

% Please define a domain-name first.

Press RETURN to get started!

APAVC: Initial WLAN Buffers Given to System is  2500

APAVC:  WlanPAKs 18174 RadioPaks  17566

set_radio_pwr_mode: bad radio unit# 0

set_radio_pwr_mode: bad radio unit# 1

*Mar  1 00:00:13.663: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg

*Mar  1 00:00:15.707: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar  1 00:00:16.067: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Sat 16-Nov-13 10:46 by prod_rel_team

*Mar  1 00:00:16.107: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg

*Mar  1 00:00:16.107: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default configlwapp_crypto_init: MIC Present and Parsed Successfully

*Mar  1 00:00:16.231: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar  1 00:00:17.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to upERROR: Failed to configure ethernet promiscuous mode. Interface Descriptor mismatch

*Mar  1 00:00:20.919: DPAA Initialization Complete

*Mar  1 00:00:20.919: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited

*Mar  1 00:00:21.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up

no bridge-group 1 source-learning

                   ^

% Invalid input detected at '^' marker.

%Default route without gateway, if not a point-to-point interface, may impact performance

*Mar  1 00:00:34.859: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg

*Mar  1 00:00:53.751: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.13.1.85, mask 255.255.254.0, hostname AP3c08.f66c.f504

Translating "CISCO-CAPWAP-CONTROLLER.childrenshc.org"...domain server (10.12.18.255)

*Mar  1 00:01:03.731: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.11.0.210 obtained through DHCP

*Mar  1 00:01:03.731: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.11.0.212 obtained through DHCP

*Mar  1 00:01:03.731: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:01:03.731: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.childrenshc.org

*Mar  1 00:01:03.735: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'c5508-2.cpt'running version 7.5.102.0 is rejected.

*Mar  1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.

*Mar  1 00:01:03.735: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.

*Mar  1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller

*Mar  1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.11.0.212

*Mar  1 00:01:13.735: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'c5508-2.cpt'running version 7.5.102.0 is rejected.

*Mar  1 00:01:13.735: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.

10 Replies 10

Wes Schochet
Level 3
Level 3

The release notes (http://www.cisco.com/en/US/docs/wireless/access_point/3700/quick/guide/ap3700getstart.html#wp41694) say code ver 7.5.0.0, but I am beyond that at 7.5.102.0.  Somehow, I think a code upgrade is still in my future!

Wes,

     on the WLC CLI can you capture and post the output of the follwoing debugs?

debug mac addr 3c08f66cf504

debug capwap events enable

debug capwap errors enable

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

What code is the WLC 7.5 ? 3700 require 7.6 code ..

__________________________________________________________________________________________
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
__________________________________________________________________________________________
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
___________________________________________________________

Hang tight I just emailed the cisco guys on the 3700 team ..

__________________________________________________________________________________________
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
__________________________________________________________________________________________
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
___________________________________________________________

Thanks

Just confirmed with the Cisco guys, thats a mistake. 7.6 code is needed, 7.5 not supported with 3700.

__________________________________________________________________________________________
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
__________________________________________________________________________________________
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
___________________________________________________________

Nothing like a good hex dump to get the day going!

Hi Wes,

Talk to TAC & get a pre-release 7.6.x code & check this AP registration again..

There may be a chance this AP get corrupted since it was connected to a controller image which is not supported.(but you should be able to recover it)

HTH

Rasika

**** Pls rate all useful responses ****

Create a TAC Case. 

TAC will give you special release access to a pre-release 7.6 firmware.

yes.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: