cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
327
Views
0
Helpful
2
Replies

5508 Controller Controller

boitumelo69
Level 1
Level 1

Im configuring a 5508 controller on a layer 2 network. Im only able to access the controller through the service port and not through the management interface. I can see the controller on the CDP neighbour table on the switch that it connects too. I have configured another controller in my lab and found that i have the same problem with the second controller.

 

SDNCTNSW-Century_SW1#show int Gi2/0/1            
GigabitEthernet2/0/1 is up, line protocol is up (connected)
  Hardware is Gigabit Ethernet, address is 0017.5983.2281 (bia 0017.5983.2281)
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not set
  Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX SFP
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:09, output 00:00:15, output hang never
  Last clearing of "show interface" counters 6d01h
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 2000 bits/sec, 2 packets/sec
     8830 packets input, 12805388 bytes, 0 no buffer
     Received 8830 broadcasts (0 multicast)
     76755 runts, 0 giants, 0 throttles
     76755 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 8769 multicast, 0 pause input
     0 input packets with dribble condition detected
     7859928 packets output, 833702013 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
SDNCTNSW-Century_SW1#
SDNCTNSW-Century_SW1#show run int Gi2/0/1
Building configuration...

Current configuration : 124 bytes
!
interface GigabitEthernet2/0/1
 switchport trunk encapsulation dot1q
 switchport mode trunk
 channel-group 5 mode on
end

SDNCTNSW-Century_SW1#show cdp nei Gi2/0/1 de
-------------------------
Device ID: ZA377-SMHWC-MBCENTURYCITY-WLC01
Entry address(es):
  IP address: 53.32.224.15
Platform: AIR-CT5508-K9,  Capabilities: Host
Interface: GigabitEthernet2/0/1,  Port ID (outgoing port): GigabitEthernet0/0/1
Holdtime : 124 sec

Version :
Manufacturer's Name: Cisco Systems Inc.  Product Name: Cisco Controller  Product Version: 7.6.130.0  RTOS Version: Erro  Bootloader Version: 1.0.1  Build Type: DATA + WPS

advertisement version: 2
Duplex: full
Management address(es):

-------------------------
Device ID: ZA377-SMHWC-MBCENTURYCITY-WLC01
Entry address(es):
  IP address: 53.32.224.15
Platform: AIR-CT5508-K9,  Capabilities: Host
Interface: GigabitEthernet2/0/1,  Port ID (outgoing port): LAGInterface0/3/1
Holdtime : 124 sec

Version :
Manufacturer's Name: Cisco Systems Inc.  Product Name: Cisco Controller  Product Version: 7.6.130.0  RTOS Version: Erro  Bootloader Version: 1.0.1  Build Type: DATA + WPS

advertisement version: 2
Duplex: full
Management address(es):

2 Replies 2

Sandeep Choudhary
VIP Alumni
VIP Alumni

Hi,

Try to allow specific vlan on WLC connected port and try again:

Example:

interface f0/12
switchport trunk encapsulation dot1q
switchport trunk native vlan 10
switchport trunk allowed vlan 1,2,10
switchport mode trunk
 

Regards

Don't forget to rate helpful posts

Hi

 

This change in vlan configuration didnt help and im still not able to get to the device via the management port.

 

SDNCTNSW-Century_SW1#sh run int Gi2/0/1
Building configuration...

Current configuration : 195 bytes
!
interface GigabitEthernet2/0/1
 switchport trunk encapsulation dot1q
 switchport trunk native vlan 10
 switchport trunk allowed vlan 1,2,10
 switchport mode trunk
 channel-group 5 mode on
end

SDNCTNSW-Century_SW1#ping 53.32.224.15

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 53.32.224.15, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

Review Cisco Networking products for a $25 gift card