Converged access 3850 QOS platinum policy state: Validation Failed

[Nick Shelley]

Hi all,

So got a 3850 running 03.03.04SE.  Trying to set up platinum QOS for voip on a wlan.

When applying platinum, I get this problem:

QoS Service Policy - Input
  Policy Name                                  : platinum-up
  Policy State                                 : Validated
QoS Service Policy - Output
  Policy Name                                  : platinum
  Policy State                                 : Validation Failed

Any ideas why platinum fails validation?
 

[Rasika Nayanajith]

Hi,

Did you try to add these two lines via CLI  ? Make that SSID advertising on your AP & then check. I tried it on IOS-XE 3.6 & it worked.

wlan ABC-123
service-policy input platinum-up
service-policy output platinum

5760#show wlan id 21 | be QoS
QoS Service Policy - Input
  Policy Name                                  : platinum-up
  Policy State                                 : Validated
QoS Service Policy - Output
  Policy Name                                  : platinum
  Policy State                                 : Validated

still if it is not working I think it is code specific issue

HTH

Rasika

*** Pls rate all useful responses ****

[Nick Shelley]

Yes, I configured that via command-line.  Any one know of a work-around that I could try?

I tried replicating the platinum qos settings under a different policy, and it still returns "validation failed"

Bug?

[Rasika Nayanajith]

You can upgrade to 3.6 if you like. That code does not have this issue.

HTH

Rasika

**** Pls rate all useful responses ***

[greg.murray]

Hi

I have the same issue in that when I issue the following command I get the validation error for the SSID.

NLSPL01SWI-core1-WLC#show wlan name xxxxx | inc Policy
AAA Policy Override                            : Disabled
QoS Service Policy - Input
  Policy Name                                  : SSIDin
  Policy State                                 : Validation Failed
QoS Service Policy - Output
  Policy Name                                  : SSIDout
  Policy State                                 : Validation Failed
QoS Client Service Policy
  Input  Policy Name                           : PM-taggingPolicy
  Output Policy Name                           : unknown
Radio Policy                                   : All

I followed your advice and create a new test SSID and applied a Server Policy to it and it validates.

NLSPL01SWI-core1-WLC#show wlan name abc123 | inc Policy
AAA Policy Override                            : Disabled
QoS Service Policy - Input
  Policy Name                                  : platinum-up
  Policy State                                 : Validated
QoS Service Policy - Output
  Policy Name                                  : platinum
  Policy State                                 : Validated
QoS Client Service Policy
  Input  Policy Name                           : unknown
  Output Policy Name                           : unknown
Radio Policy                                   : All

I have read the bug details and it is obviously hitting this. My users are not complaining of voice issues which is great but I do want this policy to work correctly.

Can you tell me why I need to shut the ports down that are connect to the access points in your steps?

Why I run my configuration, I shut the SSID down, created the class-maps and policy-maps and then applied this to the SSID and then issued a no shut on the SSID.

I am running version 03.03.03 SE

Regards

Greg

[jwmolenaar]

Hi Greg,

I'm 100% sure anymore but I think because the AP's needed a reload for some reason.

Regards,

Jan-Willem

[Joseph Vasanth Louis]

Hi

you added the qos policies through GUI or CLI? Validation failed generally means that the qos policy did not get installed.

If this was done through CLI, this should be a code specific issue.

regards,

Joseph

[jwmolenaar]

Hi,

I've got the same error running 3.6.0 and opened a TAC case
Keep you updated.

Regards, Jan-Willem

[Nick Shelley]

Hi Jan-Willem,

What ever came from the TAC case regarding running 3.6.0 and the platinum QOS error?

[jwmolenaar · Accepted solution]

Hi,

I had a service-policy configured for the switchport where an AP was attached.

I was able to get the QoS policy applied and validated:

1. Disabled the switchports to shutdown the AP's
2. Removed the service-policy from the switchports connected to the AP's
3. Reconfigured the WLAN , by deleting and recreating the WLAN profiles including the qos policy.
4. Brought UP switchports and access-points.

Gr, Jan-Willem