Converged Access and Clean Air Statistics

[Salvador Antonio Quintanilla Mendoza]

Hi,

   how can i get the Clean air Statistics of the Access Points connected to the Mobility Agents (3650)??. My master controller is a WLC 5508 (version 7.6.130).

Sw_AP_RegalFSSA0_3#show ap  dot11 5ghz cleanair air-quality worst

% This command is not available on Mobility Agent

Sw_AP_RegalFSSA0_3#

Sw_AP_RegalFSSA0_3#show ap  dot11 5ghz cleanair air-quality summary

% This command is not available on Mobility Agent

Sw_AP_RegalFSSA0_3#

I can just see that cleanair is enable but not the details.

Sw_AP_RegalFSSA0_2#show ap dot11 5ghz cleanair config

Mobility Controller Link Status.................. : UP
CleanAir Solution................................ : Enabled
Air Quality Settings:
Air Quality Reporting........................ : Enabled
Air Quality Reporting Period (min)........... : 15
Air Quality Alarms........................... : Enabled
Air Quality Alarm Threshold.................. : 35
Interference Device Settings:
Interference Device Reporting................ : Enabled
TDD Transmitter.......................... : Enabled
Jammer................................... : Enabled
Continuous Transmitter................... : Enabled
DECT-like Phone.......................... : Enabled
Video Camera............................. : Enabled
WiFi Inverted............................ : Enabled
WiFi Invalid Channel..................... : Enabled
SuperAG..................................: Enabled
Canopy................................... : Enabled
WiMax Mobile............................. : Enabled
WiMax Fixed.............................. : Enabled

[Rasika Nayanajith]

RRM is a funtion of MC in converged access deployment. So you should run these commands on MC. Here is an example from my setup. In my case MC is a 5760 and above command is working as it is

XXX-WC02#show ap dot11 5ghz cleanair air-quality ? 
 summary Displays CleanAir Air Quality (AQ) data for 5GHz band
 worst Displays CleanAir Air Quality (AQ) worst data for 5GHz band

XXX-WC02#show ap dot11 5ghz cleanair air-quality summary

AQ = Air Quality
DFS = Dynamic Frequency Selection

AP Name Channel Avg AQ Min AQ Interferers DFS 
--------------------------------------------------------------
XXX-L2R02... 52 100 100 0 No 
XXX-L2R02... 56 100 100 0 No 
XXX-L2R02... 60 99 99 0 No 
XXX-L2R02... 64 100 100 0 No 
XXX-L1R01... 149 99 99 0 No 
XXX-L1R01... 153 99 99 0 No 
XXX-L1R01... 157 98 98 0 No 
XXX-L1R01... 161 99 99 0 No 
XXX-L2R02... 52 100 100 0 No 
XXX-L2R02... 56 100 100 0 No 
XXX-L2R02... 60 99 99 0 No 
XXX-L2R02... 64 99 99 0 No 
XXX-L2R20... 149 99 99 0 No 
XXX-L2R20... 153 99 99 0 No 
XXX-L2R20... 157 100 100 0 No 
XXX-L2R20... 161 100 100 0 No 
XXX-L2R20... 52 99 99 0 No 
XXX-L2R20... 56 99 99 0 No 
XXX-L2R20... 60 99 99 0 No 
XXX-L2R20... 64 99 99 0 No 
XXX-L2R20... 36 99 99 0 No 
XXX-L2R20... 40 99 99 0 No 
XXX-L2R20... 44 99 99 0 No 
XXX-L2R20... 48 99 99 0 No 
XXX-L1R11... 149 99 99 0 No 
XXX-L1R11... 153 99 99 0 No 
XXX-L1R11... 157 99 99 0 No

Here is the equivalent command for 5508, run this on your MC-5508 & see

(XXX-WC01) >show 802.11a cleanair air-quality ? 
<Cisco AP> Enter Cisco AP name
summary Display a summary of 802.11a air quality.
worst Display information for the 802.11a radio with the worst air quality.

HTH

Rasika

*** Pls rate all useful responses ****