03-19-2004 01:44 AM - edited 07-04-2021 09:27 AM
When i add ip address 10.100.100.1 255.255.255.0 secondary to interface Bv1 and i type show running-config i can't see secondary ip address.Why?
Many Thanks
ap# sh ver
Cisco Internetwork Operating System Software
IOS (tm) C1200 Software (C1200-K9W7-M), Version 12.2(11)JA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Mon 07-Jul-03 13:48 by ccai
Image text-base: 0x00003000, data-base: 0x004D46F4
ROM: Bootstrap program is C1200 boot loader
BOOTLDR: C1200 Boot Loader (C1200-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ap uptime is 14 minutes
System returned to ROM by power-on
System image file is "flash:/c1200-k9w7-mx.122-11.JA1/c1200-k9w7-mx.122-11.JA1"
Using 2325 out of 32768 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname CISCO-AP50
!
ip subnet-zero
!
dot11 network-map
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
ssid xxxxxxx
vlan 50
authentication open
authentication shared
!
ssid xxxxxxx
vlan 51
authentication open
!
ssid tsunami
authentication open
guest-mode
!
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0
rts threshold 2312
station-role root
!
interface Dot11Radio0.1
encapsulation dot1Q 1
no ip route-cache
!
interface Dot11Radio0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio0.51
encapsulation dot1Q 51
no ip route-cache
bridge-group 51
bridge-group 51 subscriber-loop-control
bridge-group 51 block-unknown-source
no bridge-group 51 source-learning
no bridge-group 51 unicast-flooding
bridge-group 51 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
!
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface FastEthernet0.50
encapsulation dot1Q 50
no ip route-cache
!
interface FastEthernet0.51
encapsulation dot1Q 51
no ip route-cache
bridge-group 51
no bridge-group 51 source-learning
bridge-group 51 spanning-disabled
!
interface BVI1
ip address 192.168.0.2 255.255.255.0
!
ip http server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivory/1100
bridge 1 route ip
!
!
line con 0
line vty 0 4
login local
line vty 5 15
login
!
end
03-25-2004 02:03 AM
Hi,
Try using show interface to see secondary IP addresses.
On a security note you may want to read this if you haven't done so already.
http://www.cisco.com/warp/public/707/cisco-sn-20030730-ios-2gb-get.shtml
R/S
Dave
04-08-2004 07:13 AM
Hi,
i tried to show interface but i didn't see the new ip secondary address.
Why?
Thanks
Marco
04-19-2004 05:11 AM
Hi Marco,
Have you found why you can't see the new ip secondary address ? I have the same proble on a 1200.
Thanks,
Eric
04-24-2004 08:11 AM
Sorry,i can't find solution.
Marco
09-07-2006 05:00 AM
Try this - it seems to create a second instance of the BVI 1 interface.
ap#conf t
Enter configuration commands, one per line. End with CNTL/Z.
ap(config)#int bvI 1:0
ap(config-if)#
ap(config-if)#ip address 10.2.2.2 255.255.255.0
ap(config-if)#end
ap#sh ip int brief
Interface IP-Address OK? Method Status Protocol
BVI1 192.168.54.1 YES NVRAM up up
BVI1 10.2.2.2 YES manual up up
both addresses can be pinged
09-07-2006 05:44 PM
Just curious: Why are you putting a second IP address on the AP, when it does no routing (the address is just there for management)?
Thanks
Scott
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: