02-01-2014 11:11 PM - edited 07-05-2021 12:04 AM
Dear Team,
I am configuring air-sap2602 and created multiple ssid but its broadcasting only one ssid instead of multiple.Any one can help me?
Thanks
Solved! Go to Solution.
02-02-2014 12:25 AM
Hi Waqas,
You may be missing "mbssid guest-mode" command under SSID configuration & "mbssid" command under radio interfaces. Since it is multiple SSID you require this.
Here is a sample configuration of two SSID (WLAN-1 with vlan 7 & WLAN-2 with vlan 8) & AP management (on vlan 10). Security configuration used WPA2/AES with PSK
hostname AAP1
!
dot11 ssid WLAN-1
vlan 7
authentication open
authentication key-management wpa version 2
wpa-psk ascii WLAN-1-KEY
mbssid guest-mode
!
dot11 ssid WLAN-2
vlan 8
authentication open
authentication key-management wpa version 2
wpa-psk ascii WLAN-2-KEY
mbssid guest-mode
!
interface Dot11Radio0
encryption vlan 7 mode ciphers aes-ccm
encryption vlan 8 mode ciphers aes-ccm
ssid WLAN-1
ssid WLAN-2
mbssid
station-role root
!
interface Dot11Radio1
encryption vlan 7 mode ciphers aes-ccm
encryption vlan 8 mode ciphers aes-ccm
ssid WLAN-1
ssid WLAN-2
mbssid
station-role root
!
interface Dot11Radio0.7
encapsulation dot1Q 7
bridge-group 7
!
interface Dot11Radio0.8
encapsulation dot1Q 8
bridge-group 8
!
interface Dot11Radio0.10
encapsulation dot1Q 10 native
bridge-group 1
!
!
interface Dot11Radio1.7
encapsulation dot1Q 7
bridge-group 7
!
interface Dot11Radio1.8
encapsulation dot1Q 8
bridge-group 8
!
interface Dot11Radio1.10
encapsulation dot1Q 10 native
bridge-group 1
!
interface GigabitEthernet0.7
encapsulation dot1Q 7
bridge-group 7
!
interface GigabitEthernet0.8
encapsulation dot1Q 8
bridge-group 8
!
interface GigabitEthernet0.10
encapsulation dot1Q 10 native
bridge-group 1
!
interface BVI1
ip address 192.168.10.254 255.255.255.0
!
ip default-gateway 192.168.10.1
Here is AP connected swtichport configuration. SVI configuratoin & DHCP configuration to be there (not shown here)
**** AP Connected Swtichport *****
int g x/x
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk native vlan 10
switchport trunk allow vlan 7,8,10
HTH
Rasika
**** Pls rate all useful responses ***
02-01-2014 11:30 PM
can you paste the config here , then only we can find the cause.
Reagrds
02-02-2014 12:25 AM
Hi Waqas,
You may be missing "mbssid guest-mode" command under SSID configuration & "mbssid" command under radio interfaces. Since it is multiple SSID you require this.
Here is a sample configuration of two SSID (WLAN-1 with vlan 7 & WLAN-2 with vlan 8) & AP management (on vlan 10). Security configuration used WPA2/AES with PSK
hostname AAP1
!
dot11 ssid WLAN-1
vlan 7
authentication open
authentication key-management wpa version 2
wpa-psk ascii WLAN-1-KEY
mbssid guest-mode
!
dot11 ssid WLAN-2
vlan 8
authentication open
authentication key-management wpa version 2
wpa-psk ascii WLAN-2-KEY
mbssid guest-mode
!
interface Dot11Radio0
encryption vlan 7 mode ciphers aes-ccm
encryption vlan 8 mode ciphers aes-ccm
ssid WLAN-1
ssid WLAN-2
mbssid
station-role root
!
interface Dot11Radio1
encryption vlan 7 mode ciphers aes-ccm
encryption vlan 8 mode ciphers aes-ccm
ssid WLAN-1
ssid WLAN-2
mbssid
station-role root
!
interface Dot11Radio0.7
encapsulation dot1Q 7
bridge-group 7
!
interface Dot11Radio0.8
encapsulation dot1Q 8
bridge-group 8
!
interface Dot11Radio0.10
encapsulation dot1Q 10 native
bridge-group 1
!
!
interface Dot11Radio1.7
encapsulation dot1Q 7
bridge-group 7
!
interface Dot11Radio1.8
encapsulation dot1Q 8
bridge-group 8
!
interface Dot11Radio1.10
encapsulation dot1Q 10 native
bridge-group 1
!
interface GigabitEthernet0.7
encapsulation dot1Q 7
bridge-group 7
!
interface GigabitEthernet0.8
encapsulation dot1Q 8
bridge-group 8
!
interface GigabitEthernet0.10
encapsulation dot1Q 10 native
bridge-group 1
!
interface BVI1
ip address 192.168.10.254 255.255.255.0
!
ip default-gateway 192.168.10.1
Here is AP connected swtichport configuration. SVI configuratoin & DHCP configuration to be there (not shown here)
**** AP Connected Swtichport *****
int g x/x
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk native vlan 10
switchport trunk allow vlan 7,8,10
HTH
Rasika
**** Pls rate all useful responses ***
06-19-2014 05:22 AM
Hi Rasika,
With mbssid guest-mode command both of wireless SSIDs work in guest mode? Can I use both of SSIDs in my internal network for two parties?
Thank you
Kind regards
Chamara
06-19-2014 05:28 AM
Hi Chamara,
Guest mode broadcasts the SSID and only one SSID can be in gueat mode.
To broadcast multiple SSIDs use mbssid guest-mode on each SSID.
Check the example:
http://rscciew.wordpress.com/2014/05/24/multiple-ssid-configurations-on-autonomous-ap/
Regards
Dont forget to rate helpful posts
06-19-2014 05:32 AM
Thanks for the reply Sandeep. But my question is are those two SSIDs can use as non guest wireless for my office use
thank again bro
Kind regards
Chamara
06-19-2014 05:37 AM
of course you can use both ssid of office use.
Its depends on your configuration.
Regards
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: