cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

8965
Views
0
Helpful
12
Replies

Needs to download the autonomous IOS for AIR-AP3802i-D-K9

Hi Team,

               We had purchased 3802i model Access point recently, we would like to work with standalone mode, so i tried to download the Autonomous IOS from cisco website, but this software doesn't available. can someone do help to resolve this?

                For Information : we had a contract for this AP and also our CISCO ID has associated with contract.

Thanks

12 REPLIES 12
Beginner

https://supportforums.cisco

https://supportforums.cisco.com/discussion/13230486/needs-download-autonomous-ios-air-ap3802i-d-k9

Kindly don't make multiple  copies of one topic

Hall of Fame Community Legend

Starting with the 1800/2800

Starting with the 1800/2800/3800, there is no more "autonomous" or "standalone" mode.  Cisco has changed that to Cisco Mobility Express.  

To convert the AP from controller-based IOS to Mobility Express, read THIS.

Don't forget to rate our useful posts.  

Hi Leo,

Hi Leo,

           Thanks for your valuable reply, meanwhile i just wants to know some details

1. I am going to directly connect this AP to ISP (not through switch) , so i need to create dhcp in AP only, Is it possible in Mobility Express?

2. I want to configure one IP address to AP for Management before the Mobility Express IOS upgrade to AP , How to do it? Please explain

Thanks

Hall of Fame Community Legend

1. I am going to directly

1. I am going to directly connect this AP to ISP (not through switch) , so i need to create dhcp in AP only, Is it possible in Mobility Express?

Yes, you can create a DHCP scope.

Thanks Leo,

Thanks Leo,

 Can you give some idea about my 2nd question?

Hall of Fame Community Legend

Please read the Getting

Please read the Getting Started Guide.

Hi Leo,

Hi Leo,

           As per the document, I have assigned the IP address to the AP through the following command

#capwap ap ip 10.0.0.2 255.255.255.0 10.0.0.1

then, i have assigned the ip address to the system 

10.0.0.1 255.255.255.0 default gateway 10.0.0.1

den i have tried to upload the image through below command

#ap-type mobility-express tftp://10.0.0.1/AIR-AP3800-K9-ME-8-3-102-0.tar

after that following commands is showing in my console

AP0042.68C6.08D0#ap-type mobility-express tftp://10.0.0.1/[*01/01/2016 10:43:06.0181] CAPWAP State: Discovery
[*01/01/2016 10:43:06.0182] Did not get log server settings from DHCP.
[*01/01/2016 10:43:15.5208] CAPWAP State: Discovery
[*01/01/2016 10:43:15.5209] Did not get log server settings from DHCP.
AP0042.68C6.08D0#ap-type mobility-express tftp://10.0.0.1/AIR-AP3800-K9-ME-8-3-102-0.tar[*01/01/2016 10:43:25.0236] CAPWAP State: Discovery
[*01/01/2016 10:43:25.0237] Did not get log server settings from DHCP.
AP0042.68C6.08D0#ap-type mobility-express tftp://10.0.0.1/AIR-AP3800-K9-ME-8-3-102-0.tar
Starting the ME image download...
It may take a few minutes to finish download.
If it is longer, please abort command, check network connection and try again
[*01/01/2016 10:43:34.5263] CAPWAP State: Discovery
[*01/01/2016 10:43:34.5264] Did not get log server settings from DHCP.
[*01/01/2016 10:43:44.0291] CAPWAP State: Discovery
[*01/01/2016 10:43:44.0292] Did not get log server settings from DHCP.
[*01/01/2016 10:43:53.5319] CAPWAP State: Discovery
[*01/01/2016 10:43:53.5323] Did not get log server settings from DHCP.
[*01/01/2016 10:44:03.0346] CAPWAP State: Discovery
[*01/01/2016 10:44:03.0347] Did not get log server settings from DHCP.
[*01/01/2016 10:44:12.5374] CAPWAP State: Discovery
[*01/01/2016 10:44:12.5375] Did not get log server settings from DHCP.

I have mentioned the #sh version details in below

Processor board ID FGL2026X9N8
AP Running Image : 8.2.20.16
Primary Boot Image : 8.2.20.16
Backup Boot Image : 0.0.0.0
1 Multigigabit Ethernet interfaces
1 Gigabit Ethernet interfaces
2 802.11 Radios
Radio Driver version : 9.0.5.5-W8964
Radio FW version : 9.1.8.1
NSS FW version :

Base ethernet MAC Address : 00:42:68:C6:08:D0
Part Number : 73-017278-05
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC20230UW4
Top Assembly Part Number : 068-100531-01
Top Assembly Serial Number : FGL2026X9N8
Top Revision Number : A0
Product/Model Number : AIR-AP3802I-D-K9


AP0042.68C6.08D0#[*01/01/2016 10:37:42.9236] CAPWAP State: Discovery
[*01/01/2016 10:37:42.9237] Did not get log server settings from DHCP.

Kindly check my process whether i am doing correct or not? still i am not able to upload the Mobility Express image, Please help

Hall of Fame Community Legend

The AP wants the IP address

The AP wants the IP address to be DHCP.  

but i am not using any DHCP

but i am not using any DHCP server, i have configured IP manually to AP, Is there any possiblities ?

Highlighted
Beginner

Please Update you firmware to

Please Update you firmware to 8.3.

Use the following guide to setup :

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/83/user_guide/b_ME_User_Guide_83/b_ME_User_Guide_83_chapter_01000.html

If the issue persists further please contact Cisco TAC as you have a contract

Hi Team,

Hi Team,

              I have upgraded to 8.3, but i can able to work with Mobile devices only not laptop's.I am getting the error form Master AP while i am pinging from laptop(192.168.1.1) as attached Image but i can able to ping that AP from laptop(192.168.1.10).

Contributor

Re: Needs to download the autonomous IOS for AIR-AP3802i-D-K9

To configure standalone Cisco access point :-
1.  Assign static IP address to AP
2.  Create SSID name of WLAN1
3.  Broadcast the SSID
4.  NO security
5.  Enable wireless interfaces
6.  Check connectivity
7.  Configure AP with a WPA2 PSK authentication

CreatePlease to create content
Content for Community-Ad

August's Community Spotlight Awards