- Cisco Community
- Technology and Support
- Wireless - Mobility
- Wireless
- Thanks Rasika for your
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
Remote Site Having Wifi Slowness
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-02-2016 08:28 AM - edited 07-05-2021 06:04 AM
Very vague issue I know.
From what I have gathered so far, download speeds on the wifi are fine at times and sporadically slow at 4Mbps downloads on a 100Mbps circuit. I do see some drops on the Internet circuit connecting interface, but not a very high amount.
I am looking at all angles - not just wifi...Internet facing interface on firewall for speed and duplex, but I am thinking this is a wifi issue as we are not experiencing the same slowness on the wired. Also, these people are stationary so likely not a roaming issue.
At the remote site we are using 37021 APs using FlexconnectAP mode. Internet traffic is directed to the local Internet circuit..as previously mentioned 100Mbps.
There should not be any issues with contention as there are only 5 people at the site - going to be many more in the future.
And the is plenty of AP coverage
Because this is in an urban environment, I'm am first thinking this could be an interference issue.
I admit that I am trying to take the easy way out of this issue and trying to find a smoking gun, but isnt there a configuration on the AP that fixes interference in an Urban environment with many wireless signals?
If not, where should I start? Wireshark, Controller logs, switch logs. I will paste any and all
Thank you
- Labels:
-
Wireless IP Voice and Video
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-02-2016 01:05 PM
I would suggest below
1. Using a wired PC (on the same vlan wireless users use) test the performance over 1 hr period and see bench mark speeds you get.
2. Do a comparison test with a wireless user
3. If you see considerable performance drop, first check the configuration and make sure WPA2-AES with WMM enabled on WLAN. Also check "show client detail <mac_addr>" output to confirm RSSI & SNR of the clients. Also check the wireless client capability (spatial streams,802.11n/ac, etc)
4. All values in number 3 indicate client should get higher througput, try to go with different version of software code and see.
HTH
Rasika
*** Pls rate all useful responses ***
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-02-2016 03:34 PM
Thanks Rasika for your response.
Could you explain what you mean by "all values in number 3"?
I cannot find the setting for "WMM" under the WLAN...
Also, do you think we should enable "Avoid Persistent Non-WiFi Interference" under wireless
Thank you, Pat.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-02-2016 06:06 PM
Post "show client <mac_addr>" output for your wireless client when it experience this slowness.
Also post "show wlan <wlan_id>" to see how you configure the SSID for this.
To see software version "show sysinfo" output would be useful as well.
HTH
Rasika
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-03-2016 05:29 AM
Thanks Rasika
I will be sure to post the "show client" when the user is experiencing issues.
Could you please answer the questions below when you have a moment?
Thank you
Could you explain what you mean by "all values in number 3"?
I cannot find the setting for "WMM" under the WLAN...
Also, do you think we should enable "Avoid Persistent Non-WiFi Interference" under wireless
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-03-2016 05:10 PM
I cannot find the setting for "WMM" under the WLAN...
WLAN > QoS > WMM Policy [ you can have either required or allowed ]
do you think we should enable "Avoid Persistent Non-WiFi Interference" under wireless
If you have enabled EDRRM, then it is good to tick that box, so if AP detect some non-wifi interference on particular channel, then AP will change its channel to avoid that interference.
Refer this post for more detail
https://mrncciew.com/2013/05/02/event-driven-rrm/
HTH
Rasika
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-14-2016 08:35 AM
Here is some show client info:
Client MAC Address............................... 7c:7a:91:bf:33:9e
Client Username ................................. USER
AP MAC Address................................... 84:3d:c6:08:23:d0
AP Name.......................................... BOS-AP07
AP radio slot Id................................. 1
Client State..................................... Associated
Client User Group................................ USER
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 1
Wireless LAN Network Name (SSID)................. SSID
Wireless LAN Profile Name........................ SSID
Hotspot (802.11u)................................ Not Supported
BSSID............................................ 84:3d:c6:08:23:df
Connected For ................................... 3274 secs
Channel.......................................... 161
IP Address....................................... 10.25.222.61
Gateway Address.................................. 10.25.222.1
Netmask.......................................... 255.255.254.0
Association Id................................... 2
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
--More-- or (q)uit
Client CCX version............................... 4
Client E2E version............................... No E2E support
Re-Authentication Timeout........................ 301
QoS Level........................................ Silver
Avg data Rate.................................... 0
Burst data Rate.................................. 0
Avg Real time data Rate.......................... 0
Burst Real Time data Rate........................ 0
Avg Uplink data Rate............................. 0
Burst Uplink data Rate........................... 0
Avg Uplink Real time data Rate................... 0
Burst Uplink Real Time data Rate................. 0
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
Qos Map Capability............................... No
WMM Support...................................... Enabled
APSD ACs....................................... BK(T/D) BE(T/D) VI(T/D) VO(T/D)
Current Rate..................................... m8 ss2
Supported Rates.................................. 6.0,9.0,12.0,18.0,24.0,36.0,
............................................. 48.0,54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
--More-- or (q)uit
Security Policy Completed........................ Yes
Policy Manager State............................. RUN
Audit Session ID................................. 0a14cb0b0002b1c55829d83d
AAA Role Type.................................... none
Local Policy Applied............................. none
IPv4 ACL Name.................................... none
FlexConnect ACL Applied Status................... Unavailable
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Layer2 ACL Name.................................. none
Layer2 ACL Applied Status........................ Unavailable
URL ACL Name..................................... none
URL ACL Applied Status........................... Unavailable
Client Type...................................... SimpleIP
mDNS Status...................................... Disabled
mDNS Profile Name................................ none
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... CCKM
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
--More-- or (q)uit
EAP Type......................................... PEAP
FlexConnect Data Switching....................... Local
FlexConnect Dhcp Status.......................... Local
FlexConnect Vlan Based Central Switching......... No
FlexConnect Authentication....................... Central
FlexConnect Central Association.................. No
FlexConnect VLAN NAME............................ SSID
Quarantine VLAN.................................. 0
Access VLAN...................................... 0
Local Bridging VLAN.............................. 222
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Not implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 225
Fast BSS Transition........................ Not implemented
11v BSS Transition......................... Not implemented
Client Wifi Direct Capabilities:
WFD capable................................ No
Manged WFD capable......................... No
Cross Connection Capable................... No
--More-- or (q)uit
Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 1739527
Number of Bytes Sent....................... 17284424
Total Number of Bytes Sent................. 17284424
Total Number of Bytes Recv................. 1739527
Number of Bytes Sent (last 90s)............ 16724
Number of Bytes Recv (last 90s)............ 33112
Number of Packets Received................. 10162
Number of Packets Sent..................... 19363
Number of Interim-Update Sent.............. 0
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Id Request Msg Failures...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Request Msg Failures......... 0
Number of EAP Key Msg Timeouts............. 0
Number of EAP Key Msg Failures............. 0
Number of Data Retries..................... 7927
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 1
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
--More-- or (q)uit
Number of Mic Missing Packets.............. 0
Number of RA Packets Dropped............... 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -59 dBm
Signal to Noise Ratio...................... 35 dB
Client Rate Limiting Statistics:
Number of Data Packets Received............ 0
Number of Data Rx Packets Dropped.......... 0
Number of Data Bytes Received.............. 0
Number of Data Rx Bytes Dropped............ 0
Number of Realtime Packets Received........ 0
Number of Realtime Rx Packets Dropped...... 0
Number of Realtime Bytes Received.......... 0
Number of Realtime Rx Bytes Dropped........ 0
Number of Data Packets Sent................ 0
Number of Data Tx Packets Dropped.......... 0
Number of Data Bytes Sent.................. 0
Number of Data Tx Bytes Dropped............ 0
Number of Realtime Packets Sent............ 0
Number of Realtime Tx Packets Dropped...... 0
Number of Realtime Bytes Sent.............. 0
Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
--More-- or (q)uit
BOS-AP01(slot 0)
antenna0: 18 secs ago.................... -61 dBm
antenna1: 18 secs ago.................... -60 dBm
BOS-AP01(slot 1)
antenna0: 20 secs ago.................... -63 dBm
antenna1: 20 secs ago.................... -60 dBm
BOS-AP06(slot 0)
antenna0: 18 secs ago.................... -48 dBm
antenna1: 18 secs ago.................... -44 dBm
BOS-AP06(slot 1)
antenna0: 20 secs ago.................... -58 dBm
antenna1: 20 secs ago.................... -57 dBm
BOS-AP07(slot 0)
antenna0: 18 secs ago.................... -54 dBm
antenna1: 18 secs ago.................... -50 dBm
BOS-AP07(slot 1)
antenna0: 20 secs ago.................... -58 dBm
antenna1: 20 secs ago.................... -65 dBm
BOS-AP03(slot 0)
antenna0: 1226 secs ago.................. -81 dBm
antenna1: 1226 secs ago.................. -82 dBm
BOS-AP04(slot 0)
antenna0: 1226 secs ago.................. -74 dBm
--More-- or (q)uit
antenna1: 1226 secs ago.................. -76 dBm
BOS-AP04(slot 1)
antenna0: 20 secs ago.................... -79 dBm
antenna1: 20 secs ago.................... -84 dBm
BOS-AP02(slot 0)
antenna0: 18 secs ago.................... -83 dBm
antenna1: 18 secs ago.................... -85 dBm
DNS Server details:
DNS server IP ............................. x.x.x.x
DNS server IP ............................. x.x.x.x
Assisted Roaming Prediction List details:
Client Dhcp Required: True
Allowed (URL)IP Addresses
-------------------------
AVC Profile Name: ............................... SSID
Fastlane Client: ................................ No
I attached a link test from the Controller to the client as well...seems to be alot of Transmit Replies at AP everytime I run the test.
Also, I would like to mention that we are using a mix of 3702I-A-K9 and B-K9 APs. I've read that it shouldn't cause any issues, but I thought it was worth mentioning.
Thx, Pat
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-03-2016 05:32 AM
Here is the WLAN and sysinfo:
(Cisco Controller) >show wlan 1
WLAN Identifier.................................. 1
Profile Name..................................... SkillSecure
Network Name (SSID).............................. SkillSecure
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Enabled
DHCP ....................................... Enabled
HTTP ....................................... Enabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum Clients Allowed.......................... Unlimited
Maximum number of Clients per AP Radio........... 200
--More-- or (q)uit
ATF Policy....................................... 0
Number of Active Clients......................... 393
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 720 minutes
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... none
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ skillsecure
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
WLAN URL ACL..................................... unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Enabled
Static IP client tunneling....................... Disabled
Tunnel Profile................................... Unconfigured
--More-- or (q)uit
PMIPv6 Mobility Type............................. none
PMIPv6 MAG Profile........................... Unconfigured
PMIPv6 Default Realm......................... Unconfigured
PMIPv6 NAI Type.............................. Hexadecimal
PMIPv6 MAG location.......................... AP
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Disabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
--More-- or (q)uit
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... 802.1P (Tag=0)
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ 10.20.116.12 1812
Authentication................................ 10.1.116.112 1812 *
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Radius NAI-Realm................................. Disabled
Mu-Mimo.......................................... Enabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
--More-- or (q)uit
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
OSEN IE.................................... Disabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Enabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Enabled
PMF-PSK(802.11w)........................ Disabled
OSEN-1X................................. Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
--More-- or (q)uit
Web Based Authentication...................... Disabled
Web Authentication Timeout.................... 300
Web-Passthrough............................... Disabled
Mac-auth-server............................... 0.0.0.0
Web-portal-server............................. 0.0.0.0
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
FlexConnect Central Association............... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Optional
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
--More-- or (q)uit
Eap-params.................................... Enabled
EAP-Identity-Request Timeout (seconds)..... 45
EAP-Identity-Request Max Retries........... 4
EAP-Request Timeout (seconds).............. 45
EAP-Request Max Retries.................... 4
EAPOL-Key Timeout (milliseconds)........... 2000
EAPOL-Key Max Retries...................... 3
AVC Visibilty.................................... Enabled
AVC Profile Name................................. SkillSecure
Flex Avc Profile Name............................ None
Flow Monitor Name................................ None
Split Tunnel Configuration
Split Tunnel................................. Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Enabled
802.11k Neighbor List Dual Band.................. Disabled
802.11v Directed Multicast Service............... Enabled
802.11v BSS Max Idle Service..................... Enabled
--More-- or (q)uit
802.11v BSS Transition Service................... Disabled
802.11v BSS Transition Disassoc Imminent......... Disabled
802.11v BSS Transition Disassoc Timer............ 200
802.11v BSS Transition OpRoam Disassoc Timer..... 40
Number of active DMS Clients..................... 4
DMS ID Client MAC Addresses
1 1c:5c:f2:87:ed:d7
c4:b3:01:3e:0b:cd
dc:9b:9c:16:e2:89
68:fb:7e:28:75:73
Band Select...................................... Enabled
Load Balancing................................... Client-Count Based
Multicast Buffer................................. Disabled
Universal Ap Admin............................... Enabled
Broadcast Tagging................................ Disabled
Mobility Anchor List
WLAN ID IP Address Status Priority
------- --------------- ------ --------
802.11u........................................ Disabled
--More-- or (q)uit
MSAP Services.................................. Disabled
Local Policy
----------------
Priority Policy Name
-------- ---------------
Lync State ...................................... Disabled
Audio QoS Policy................................. Silver
Video QoS Policy................................. Silver
App-Share QoS Policy............................. Silver
File Transfer QoS Policy......................... Silver
QoS Fastlane Status.............................. Disable
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.3.102.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
OUI File Update Time............................. Sun Sep 07 10:44:07 IST 2014
Build Type....................................... DATA + WPS
System Name...................................... NAS-WIRE-WAC1
System Location.................................. Nashua 300 Computer Room
System Contact................................... Global Network Team
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. SSO
IP Address....................................... 10.20.203.11
IPv6 Address..................................... ::
Last Reset....................................... Software reset
System Up Time................................... 6 days 11 hrs 31 mins 29 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
System Stats Realtime Interval................... 5
--More-- or (q)uit
System Stats Normal Interval..................... 180
Configured Country............................... Multiple Countries : CA,DE,FR,GB,IE,IN,US
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +42 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 666
OUI Classification Failure Count................. 47605
Burned-in MAC Address............................ F8:66:F2:FA:3B:00
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 500
System Nas-Id.................................... NAS-WIRE-WAC1
WLC MIC Certificate Types........................ SHA1
--More-- or (q)uit
(Cisco Controller) >?
clear Clear selected configuration elements.
config Configure switch options and settings.
cping Send capwap echo packets to a specified mobility peer IP address.
debug Manages system debug options.
eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.
grep Print lines matching a pattern.
help Help
license Manage Software License
linktest Perform a link test to a specified MAC address.
logout Exit this session. Any unsaved changes are lost.
mping Send Mobility echo packets to a specified mobility peer IP address.
ping Send ICMP echo packets to a specified IP address.
redundancy Manage HA Redundancy
reset Reboot (hard reload) options.
rping Send Redundancy ping packets to peer RP and RMI
save Save switch configurations.
show Display switch options and settings.
test Test trigger commands
transfer Transfer a file to or from the switch.
(Cisco Controller) >?
clear Clear selected configuration elements.
config Configure switch options and settings.
cping Send capwap echo packets to a specified mobility peer IP address.
debug Manages system debug options.
eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.
grep Print lines matching a pattern.
help Help
license Manage Software License
linktest Perform a link test to a specified MAC address.
logout Exit this session. Any unsaved changes are lost.
mping Send Mobility echo packets to a specified mobility peer IP address.
ping Send ICMP echo packets to a specified IP address.
redundancy Manage HA Redundancy
reset Reboot (hard reload) options.
rping Send Redundancy ping packets to peer RP and RMI
save Save switch configurations.
show Display switch options and settings.
test Test trigger commands
transfer Transfer a file to or from the switch.
(Cisco Controller) >?
clear Clear selected configuration elements.
config Configure switch options and settings.
cping Send capwap echo packets to a specified mobility peer IP address.
debug Manages system debug options.
eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.
grep Print lines matching a pattern.
help Help
license Manage Software License
linktest Perform a link test to a specified MAC address.
logout Exit this session. Any unsaved changes are lost.
mping Send Mobility echo packets to a specified mobility peer IP address.
ping Send ICMP echo packets to a specified IP address.
redundancy Manage HA Redundancy
reset Reboot (hard reload) options.
rping Send Redundancy ping packets to peer RP and RMI
save Save switch configurations.
show Display switch options and settings.
test Test trigger commands
transfer Transfer a file to or from the switch.
(Cisco Controller) >?
clear Clear selected configuration elements.
config Configure switch options and settings.
cping Send capwap echo packets to a specified mobility peer IP address.
debug Manages system debug options.
eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.
grep Print lines matching a pattern.
help Help
license Manage Software License
linktest Perform a link test to a specified MAC address.
logout Exit this session. Any unsaved changes are lost.
mping Send Mobility echo packets to a specified mobility peer IP address.
ping Send ICMP echo packets to a specified IP address.
redundancy Manage HA Redundancy
reset Reboot (hard reload) options.
rping Send Redundancy ping packets to peer RP and RMI
save Save switch configurations.
show Display switch options and settings.
test Test trigger commands
transfer Transfer a file to or from the switch.
(Cisco Controller) >?
clear Clear selected configuration elements.
config Configure switch options and settings.
cping Send capwap echo packets to a specified mobility peer IP address.
debug Manages system debug options.
eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.
grep Print lines matching a pattern.
help Help
license Manage Software License
linktest Perform a link test to a specified MAC address.
logout Exit this session. Any unsaved changes are lost.
mping Send Mobility echo packets to a specified mobility peer IP address.
ping Send ICMP echo packets to a specified IP address.
redundancy Manage HA Redundancy
reset Reboot (hard reload) options.
rping Send Redundancy ping packets to peer RP and RMI
save Save switch configurations.
show Display switch options and settings.
test Test trigger commands
transfer Transfer a file to or from the switch.
(Cisco Controller) >?
clear Clear selected configuration elements.
config Configure switch options and settings.
cping Send capwap echo packets to a specified mobility peer IP address.
debug Manages system debug options.
eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.
grep Print lines matching a pattern.
help Help
license Manage Software License
linktest Perform a link test to a specified MAC address.
logout Exit this session. Any unsaved changes are lost.
mping Send Mobility echo packets to a specified mobility peer IP address.
ping Send ICMP echo packets to a specified IP address.
redundancy Manage HA Redundancy
reset Reboot (hard reload) options.
rping Send Redundancy ping packets to peer RP and RMI
save Save switch configurations.
show Display switch options and settings.
test Test trigger commands
transfer Transfer a file to or from the switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-03-2016 05:12 PM
Based on the provided output here is my input.
WLAN configuration is ok to support 802.11n rates (Encryption & WMM perspective). I have noticed you have enabled CCKM, do you have cisco phones in this WLAN ?
WMM.............................................. Allowed
.
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
OSEN IE.................................... Disabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Enabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Enabled
PMF-PSK(802.11w)........................ Disabled
OSEN-1X................................. Disabled
Regarding WLC config, I noticed it is configured for multiple country codes that belong to different regulatory domain. This will restrict AP power level & channels to a lowest common value in these regulatory domain. This is not recommended and you may experience unwanted results.
Configured Country............................... Multiple Countries : CA,DE,FR,GB,IE,IN,US
Also noticed you are running latest 8.3.x code which is less than 6 months old. Always be aware of known issues in such a latest code. Below link may useful to find any known issues
https://supportforums.cisco.com/discussion/13136886/83mr1-beta-availability
Once you provide client detail, we can assess the situation much better.
HTH
Rasika
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
