cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Community Live- Understanding How Multicast Works with Cisco
237
Views
0
Helpful
3
Replies
Highlighted
Beginner

universal workgroup bridge DHCP address

Hi guys.


I'm configuring uWGB at cisco 891W. AP module successfully connected to remote AP:

 

++++++++++++++++++++
ap(config)#do sh dot11 ass all | i State|Connected
State : Assoc Parent : -
Signal Strength : -37 dBm Connected for : 1863 seconds
ap(config)#
++++++++++++++++++++

 

int bvi 1 configured to get IP from DHCP

 

++++++++++++++++++++
ap(config-if)#do sh runn int bvi 1
Building configuration...

Current configuration : 89 bytes
!
interface BVI1
mac-address 00ed.b184.2174
ip address dhcp client-id Dot11Radio0
end
++++++++++++++++++++

 

however IP has not assigned to interface BVI1

 

++++++++++++++++++++
ap(config-if)#do sh ip int bri | i BVI
BVI1 unassigned YES DHCP up up
ap(config-if)#end
++++++++++++++++++++

 

same time I've found right IP 192.168.172.50 assigned to client w/ MAC 00ed.b184.2174 (this is ap's BVI1. see above)

 

++++++++++++++++++++
gate-dhcp#sh ip dhcp bin | i ed
Bindings from all pools not associated with VRF:
192.168.172.50 0100.edb1.8421.74 Aug 25 2019 03:03 AM Automatic
gate-dhcp#
++++++++++++++++++++

 

Could somebody explain why?

wireless link works correctly because whenever I assigned same IP 192.168.172.50 I got from DHCP server manually at access point interface BVI1

++++++++++++++++++++


ap(config)#do sh runn int bvi1
interface BVI1
mac-address 00ed.b184.2174
ip address 192.168.172.50 255.255.255.248
end
++++++++++++++++++++

 

I can reach stations behind uWBG (bellow).

++++++++++++++++++++


ap(config)#do pin 192.168.172.197 re 10
Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 192.168.172.197, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 1/3/4 ms
ap(config)#
++++++++++++++++++++

 

complete ap configuration attached.

 

Thank you in advance.

Everyone's tags (2)
3 REPLIES 3
Beginner

Re: universal workgroup bridge DHCP address

addition.

wireless network reserved for wireless bridges 192.168.172.48/29

Rising star

Re: universal workgroup bridge DHCP address

Universal WGBs are designed for a single wired client to be provided wireless access so your AP picking up a second IP isn't supported by Cisco. For some reason the setup does allow that static access however..

Thanks,
Ric
-----------------------------
Please rate helpful / correct posts
Beginner

Re: universal workgroup bridge DHCP address

Thank you Ric.

 

I know this rule. Question in this case why access point's module interface BVI1 is not relaying DHCP packets towards to router module interface vlan 1?  (router interface vlan 1 in dhcp mode)

++++++++++++

Router#sh ip int brie | i lan1
Vlan1 unassigned YES DHCP up up
Router#

++++++++++++

Link between router and ap modules works. So after assigning same subnet IPs to AP's BVI1 and router VLAN1 I can ping vise versa 

AP and router modules updated config attached.

p.s. changes were:
ip address dhcp erased from BVI1 config
interface BVI1
mac-address 00ed.b184.2174
no ip address

as well as default gateway configuration

ip default-gateway 192.168.172.49


Thank you.

CreatePlease to create content
Content for Community-Ad
August's Community Spotlight Awards