cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
98
Views
0
Helpful
0
Replies
Highlighted
Beginner

Cisco 2921 <> Free-Radius (dummy/tests works but not ssh)

Because I see some deme/dummy tests, I assume CentOS-7's free-radius is working correctly, but something wrong on ISR 2921.

Still can't ssh with free-radius credentials.

## Log on 2921 ##

May 27 21:18:34.799: %RADIUS-4-RADIUS_ALIVE: RADIUS server 10.20.30.100:1812,1813 is being marked alive.
May 27 21:30:42.837: %RADIUS-4-RADIUS_ALIVE: RADIUS server 10.20.30.100:1812,1813 is being marked alive.
ISR-2921#

## Log on cent-7 ##

[root@free-radius 10.20.30.1]# cat detail-20170527 
Sat May 27 14:18:34 2017
User-Name = 'dummy'
Acct-Status-Type = Interim-Update
Acct-Session-Id = '00000000'
Acct-Authentic = RADIUS
Service-Type = Framed-User
NAS-IP-Address = 10.20.30.1
Acct-Delay-Time = 15
Event-Timestamp = 'May 27 2017 14:18:19 PDT'
Acct-Unique-Session-Id = '99c501164df6390fd6764fea1dff5aa8'
Timestamp = 1495919914

Sat May 27 14:30:42 2017
User-Name = 'freeRADIUS'
Acct-Status-Type = Interim-Update
Acct-Session-Id = '00000000'
Acct-Authentic = RADIUS
Service-Type = Framed-User
NAS-IP-Address = 10.20.30.1
Acct-Delay-Time = 0
Event-Timestamp = 'May 27 2017 14:30:42 PDT'
Acct-Unique-Session-Id = 'ba1171226b1950324d13959f95b82db7'
Timestamp = 1495920642

[root@free-radius 10.20.30.1]# ls
detail-20170527
[root@free-radius 10.20.30.1]#

## config on 2921 ##

!
aaa new-model
!
!
aaa group server radius RASERV
server name RASERV-1
retransmit 5
timeout 10
!
aaa authentication login default group radius local-case
aaa authentication login use-radius group radius local
aaa authentication login vty group radius local
aaa authentication ppp user-radius if-needed group radius
aaa authentication dot1x default group RASERV
aaa authorization exec default group radius local
aaa authorization network default group radius if-authenticated
aaa accounting dot1x default start-stop group RASERV
aaa accounting exec default start-stop group radius
aaa accounting system default start-stop group radius
!
!
ip radius source-interface GigabitEthernet0/2.888
!
!
access-list 1 permit any
!
radius server RASERV-1
address ipv4 10.20.30.100 auth-port 1812 acct-port 1813
automate-tester username freeRADIUS probe-on
key 7 110D778223
!
line vty 0 4
login authentication vty
transport input ssh
!

## config on cent-7 ##

[root@free-radius 10.20.30.1]# cat /etc/raddb/clients.conf

client 10.20.30.1 {
ipaddr = 10.20.30.1
secret = 1ass341
require_message_authenticator = no
nas_type = other
}


[root@free-radius 10.20.30.1]# cat /etc/raddb/users
freeCISCO Auth-Type := System
Service-Type = NAS-Prompt-User,
cisco-avpair = "shell:priv-lvl=15"
Everyone's tags (1)