cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
752
Views
0
Helpful
3
Replies
Cisco Employee

ISE 2.4 P8 Health Status Unavailable : Server=ise1

Hello Team, 

 

We are constantly getting alarms for the Health status but the local store is showing that the notifications are generated every five minutes. This is a two ISE node deployment and ISE 1 is the Primary MNT which is generating the alarm for him self

 

Where can I see if ISE is not parsing or if the alert arrived a little later in the logs and for this reason the alarm is triggered?

 

Alarm Health Status Unavailable     warn     Health Status Unavailable : Server=ise1     18-JUL-19 06.15.03.606549 AM -03:00

2019-07-18 06:00:17.253 -03:00 0001044262 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:05:17.280 -03:00 0001044685 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:10:17.312 -03:00 0001045285 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:15:17.340 -03:00 0001045706 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:20:17.358 -03:00 0001046305 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:25:17.390 -03:00 0001046725 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:30:17.404 -03:00 0001047324 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:35:17.435 -03:00 0001047747 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:40:17.454 -03:00 0001048352 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:45:17.474 -03:00 0001048773 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:50:17.488 -03:00 0001049372 70000 NOTICE System-Stats: ISE Utilization
2019-07-18 06:55:17.510 -03:00 0001049792 70000 NOTICE System-Stats: ISE Utilization

 

 

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
VIP Advocate

Re: ISE 2.4 P8 Health Status Unavailable : Server=ise1

I would recommend any individual facing health status unavailable alarms within their ISE deployment to work with TAC. There are many reason that this can happen and it's quite hard to say.

At least in my last case, the hotfix issued is supposed to have the bug fixed in patch 10, but I have yet to try it.
https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvq73457
3 REPLIES 3
VIP Advocate

Re: ISE 2.4 P8 Health Status Unavailable : Server=ise1

There are a few issues that can cause this but you will have to work with TAC to diagnose. Your thought process is correct here, the most common cause is if the syslog buffers do not get ingested by the collector process quickly enough, then the health status alarm will be triggered since ISE think's the node is missing.

I am working through this on 2.4 p8/9 right now, and it was also a frequent issue for a number of my customers on earlier patches. I was not expecting to face this issue again since most of those were corrected in earlier patches.

If by chance you are leveraging TACACS on this deployment, then we may be facing the same issue and I could share the case number for TAC to check on.

Beginner

Re: ISE 2.4 P8 Health Status Unavailable : Server=ise1

Hello Damien,

 

were you able to resolve this situation? It seems we have encountered it too. Strangely enough during weekends, when there is no heavy load.

Highlighted
VIP Advocate

Re: ISE 2.4 P8 Health Status Unavailable : Server=ise1

I would recommend any individual facing health status unavailable alarms within their ISE deployment to work with TAC. There are many reason that this can happen and it's quite hard to say.

At least in my last case, the hotfix issued is supposed to have the bug fixed in patch 10, but I have yet to try it.
https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvq73457