Hi,
Could anyone please let me know which trap we need to enable to monitor FEX module on 5K.
If FEX goes down due to link failure/power down we do not receceive any trap on SNMP server.
Your help is highly appreciated.
Ethernet1/5 is where Fex module in connected on 5K
Some sample log
2013 Jan 4 12:11:32switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Connecting to Active
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-PORT_UP: port-channel103: Ethernet1/5 is up
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-channel103: first operational port changed from none to E
thernet1/5
2013 Jan 4 12:11:32switch1 %ETHPORT-5-IF_UP: Interface Ethernet1/5 is up in mode Fex Fabric
2013 Jan 4 12:17:04switch1 %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-channel103: first operational port changed from Ethernet1
/5 to none
2013 Jan 4 12:17:04switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Active to Disconnected
2013 Jan 4 12:17:04switch1 %ETH_PORT_CHANNEL-5-PORT_DOWN: port-channel103: Ethernet1/5 is down
2013 Jan 4 12:17:05switch1 %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet1/5 is down (Link failure)
2013 Jan 4 12:17:06switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Disconnected to Configured
2013 Jan 4 12:17:06switch1 %ETHPORT-5-SPEED: Interface Ethernet1/5, operational speed changed to 10 Gbps
2013 Jan 4 12:17:06switch1 %ETHPORT-5-IF_DUPLEX: Interface Ethernet1/5, operational duplex mode changed to Full
2013 Jan 4 12:17:06switch1 %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet1/5, operational Receive Flow Control state ch
anged to off
2013 Jan 4 12:17:06switch1 %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet1/5, operational Transmit Flow Control state c
hanged to off
2013 Jan 4 12:17:06switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 0 of Fex 103 that is connected with Ethernet1/5 changed
its status from Configured to Fabric Up
2013 Jan 4 12:17:07switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Fabric Up to Connecting
2013 Jan 4 12:17:07switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Connecting to Active
2013 Jan 4 12:17:07switch1 %ETH_PORT_CHANNEL-5-PORT_UP: port-channel103: Ethernet1/5 is up
2013 Jan 4 12:17:07switch1 %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-channel103: first operational port changed from none to E
thernet1/5
2013 Jan 4 12:17:07switch1 %ETHPORT-5-IF_UP: Interface Ethernet1/5 is up in mode Fex Fabric
2013 Jan 4 15:12:16switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Active to Disconnected
Thanks in advance.
