cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Who Me Too'd this topic

Active HSRP does not recognize standby, but standby HSRP recognizes HSRP active.

dcamarotto
Level 1
Level 1

I have two switches configured as follows:

 

(C3750X), Version 15.0(2)SE8

interface Vlan202
 description Rede_X
 ip address 186.230.4.62 255.255.255.240
 standby version 2
 standby 1 ip 186.230.4.59
 standby 1 priority 240
 standby 1 preempt
 glbp 202 ip 186.230.4.60
 glbp 202 priority 240
 glbp 202 preempt

 

(C3750E), Version 12.2(55)SE10

 

interface Vlan202
 description Rede_X
 ip address 186.230.4.61 255.255.255.240
 standby version 2
 standby 1 ip 186.230.4.59
 standby 1 priority 250
 standby 1 preempt
 standby 1 track 10 decrement 11
 glbp 202 ip 186.230.4.60
 glbp 202 priority 250
 glbp 202 preempt
 glbp 202 load-balancing weighted
 glbp 202 weighting track 10 decrement 11
end

 

When I check the HSRP is working correctly, see the following situation:

(C3750x), Version 15.0(2)SE8

SW01#sh standby brief 
                     P indicates configured to preempt.
                     |
Interface   Grp  Pri P State   Active          Standby         Virtual IP
Vl202       1    240 P Standby 186.230.4.61    local           186.230.4.59
SW01#sh glbp
ISW01#sh glbp bri
SW01#sh glbp brief 
Interface   Grp  Fwd Pri State    Address         Active router   Standby router
Vl202       202  -   240 Standby  186.230.4.60    186.230.4.61    local
Vl202       202  1   -   Active   0007.b400.ca01  local           -
Vl202       202  2   -   Listen   0007.b400.ca02  186.230.4.61    -

Vl202       202  3   -   Listen   0007.b400.ca03  186.230.4.61    -
SW01#

 

(C3750E), Version 12.2(55)SE10

SW02#sh standby brief 
                     P indicates configured to preempt.
                     |
Interface   Grp  Pri P State   Active          Standby         Virtual IP
Vl202       1    250 P Active  local           unknown         186.230.4.59

SW02#sh glbp brief 
Interface   Grp  Fwd Pri State    Address         Active router   Standby router
Vl202       202  -   250 Active   186.230.4.60    local           186.230.4.62
Vl202       202  1   -   Listen   0007.b400.ca01  186.230.4.62    -
Vl202       202  2   -   Active   0007.b400.ca02  local           -
Vl202       202  3   -   Active   0007.b400.ca03  local           -

 

                  GLBP running fine but HSRP not.  The only information I can get about is this:

 

SW02#
Jun 30 13:04:52.558: %GLBP-6-FWDSTATECHANGE: Vlan202 Grp 202 Fwd 2 state Listen -> Active
Jun 30 13:04:52.558: HSRP: Vl202 Nbr 186.230.4.62 Adv in, active 0 passive 0
Jun 30 13:04:52.558: HSRP: Vl202 Nbr 186.230.4.62 is no longer passive
Jun 30 13:04:52.558: HSRP: Vl202 Nbr 186.230.4.62 destroyed

Jun 30 13:22:03.969: HSRP: Vl202 Nbr 186.230.4.62 Adv in, active 0 passive 1
Jun 30 13:22:03.969: HSRP: Vl202 Nbr 186.230.4.62 created
Jun 30 13:22:03.969: HSRP: Vl202 Nbr 186.230.4.62 is passive

Jun 30 13:22:04.967: %GLBP-6-FWDSTATECHANGE: Vlan202 Grp 202 Fwd 1 state Active -> Listen
Jun 30 13:22:14.974: %GLBP-6-FWDSTATECHANGE: Vlan202 Grp 202 Fwd 1 state Listen -> Active
Jun 30 13:22:17.969: %GLBP-6-FWDSTATECHANGE: Vlan202 Grp 202 Fwd 3 state Listen -> Active
Jun 30 13:22:47.018: %GLBP-6-FWDSTATECHANGE: Vlan202 Grp 202 Fwd 1 state Active -> Listen

 

 What is wrong? I've done upgrade the IOS version and the result has been the same.

Who Me Too'd this topic