Routers - Small Business

Hello,we use RV082 as main gateway and need to open/forward around 50 ports to inside. But during setting of the rules I got an error message "The max of Port Range Forwarding is 30 entries. You can't add any more.". In the online help is explicitely...

v1.1.1.06 firmware.On the Traffic Statistics page...LAN4 Down Rx Packets:    18446744073709486080 i/f has never been up.

v1.1.1.06Was trying to reboot the thing because a Gateway-Gateway VPN connection was ignoring my edits.Tried using Firefox and IE11.Given that a restart is the 'get out of jail' when other aspects of the system are broken, please fix this one....

Hi all,I don't have much experience with VPN and would really appriciate if somebody could give me advise on the issue below.Here's a portion of VPN log from my RV042 router:Jan 4 15:17:46 2014VPN Log(g2gips0) #22258: [Tunnel Negotiation Info] >>> In...

I have recently purchased a Cisco SG300-10.  I need it to perform routing between two VLANs on the switch. Seems like this should be quick and easy to do from the built in GUI. When I configure it according to the documentation, it does not ropute be...

There is release date for the new RV180 firmware? This model needs it urgently!Thanks,

Hi I need your help here.I am trying to configure my RV220W (firmware version 1.0.4.17) Port Forwarding so that I can remote access my Synology DiskStation NAS DS412+ On the Cisoc RV220W, i have set the following:- UPNP Enabled- Firewall Custom Servi...

Hi all,just that. We have some urls accessible only from our office lan, and will be nice to allow the clients to split tunnel all but this specific urls.Possible? Thanks in advance!

Hi everyone,I've set up a System consisting of two RV110W at one of our small sights. We use 3 separated networks for different purposes (security reasons).- The first RV110W operates as a gateway connecting all the tree networks to the internet and ...

Tengo un router rv042 configurado con 2 wan y balanceo de carga y necesito enviar todo el trafico del puerto 25 (smtp) de la direccion 192.168.1.103 por wan1.Configuré el protocol binding par ello pero no me funciona. Sigue enviando por wan1 y wan2.E...

Is this possible on this model?  Looking to be one or the other when working under VPN : IP Sec :  Basic VPN SetupNew account and currently have 2 of these units running a site-site config and now need to configure to permit remote users to VPN conne...

Hi,If the RV042's Protocol binding rules are in conflicts, do the one higher in the list overrides the lower one?Example:Rule#1 TCP/UDP Port 1-65535 Source: 192.168.1.30 - 192.168.1.40 Dest: 0.0.0.0-0.0.0.0 -> WAN2Rule#2 TCP/UDP Port 1-65535 Source: ...

Hi,we run a small home/business network using an RVS4000v1. Everything is pretty simple and straight forward. We use 10 different Internet Access Policies (IAP) that's it. We recently upgraded the Firmware to 1.3.3.5.Since then all IPaddresses (that ...

Hi all,after lots of hours spent trying to setup a secure vpn between my RV320 Cisco Router and my macbook pro, I ended here.For what it seems, L2tp over Ipsec and even Cisco Ipsec in the default vpn client in the mac are unnable to stablish a tunnel...

I have an SRP541W, and when I try to upgrade the firmware from 1.2.4 to 1.2.6 I get an error:Upgrade has failed.SRP541W is restarting...You will be returned to the Login page in few minutes.After the reboot I check the logs, but there are no entries....