I have a layer 3 switch that is directly connected to 2 other layer 3 switches, all routed interfaces, ospf.The main switch (switch A), is directly connected to switches B and C. In it's routing table switch A can see routes to both switches B and C ...
Forum Posts
Hey guys, This is probably a strange one-off request but thought I would try anyway. We have a situation where our service provider consistently and continuously drops certain size IPSec packets. Long story short, contracts have been signed and acc...
Hi everybody,We have a couple of ISR 4431, connected to a layer 2 network(L2 Switch). There are also other routers connected to this switch. HSRP is run on both inside and outside interface of these routers( LAN on both side ) . The problem is that t...
I ran into a issue at a customer site that has me scratching my head. The setup is as follows ASA 55050/0 set for internet access (Outside)0/1 set for internal (inside)0/3 set for Wifi Controller Everything works as designed with no issues. We were d...
Hi, recently I did upgrade my controlers from 18.4.0 to 19.2.0 and my ISR'a - C1111-8PLTEEA to 16.12.01b and I noticed that snmp configuration are gone from routers configurations. Cant find to where it should be configured. When im creating empty f...
Hi My logs are being received to my syslog server as per below message: 2018-05-29T12:24:18+10:00 notice May 29 2018 12:24:17 AEST: %C4K_REDUNDANCY-5-CONFIGSYNC: The private-config has been successfully synchronized to the standby supervisor I ne...
Resolved! Cisco ISR ISR4451-X/K9 - Fiber SFP Port
We have ISR4451-X/K9 in our enviornment and our service provider are looking to move our connection from copper to fiber in order to provide more bandwidth. I have been looking through on this forum and on Cisco official material but could not find...
Resolved! 2911 ISR Routing
Hello,I have configured an ISR and currently have wan connectivity. I can ping 8.8.8.8 and cisco.com directly from the router. I have several vlans that can pull dhcp addresses. So I believe I should be good to go as far as setting it up for routing ...
This may be a simple question for some. We had registered for a BGP AS a couple of years back. IS the registration of an AS linked to a block of ip addresses? And if we change ISP's do we need to worry about migrating the AS or ip addresses while kee...
Hi, I have been trying to find a way to configure the call settings in the Cisco ISR 2911 to call an (overseas) number using an extension number. It is not the "call-forwarding all (target number)". I was wondering if anyone can help me with this as ...
Hi, know anyone, how to active the smart Liciensing with ISE1K? I want to install the security License. I regestered the Router to the Smart Server, and do not how to download the Security license to the router... Regards Robin
Hello Everyone, Today I deployed a Cisco ISR 4351 router in production environment and configured Flexible net flow v9 to monitor this router through solarwinds, everything is working fine but i am unable to find the OID to monitor the this router in...
Good afternoon, will like to know if there is a way to send NAT log-translations to a syslog server?currently the issue we are facing with our sdwan design is that we have our CISCO FTD device behind the SD-WAN appliances so our visibility for NAT'te...
Hi fellow experts,I came here to ask for your expertise, we have started to implement SDWAN in our organization, and after many problems we just managed to get it working on our intranet (MPLS links between our branches and HQ). We got our vBond, vSm...
Hi Guys!Hope you are doing great. I need some help regarding Static Routes & Destination Based Routing? How can you differentiate those two terms?1- Static Routes2- Destination Based Routing
