1. versionenway891#sh verCisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.3(3)M5, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2015 by Cisco Systems, Inc.Compiled Wed 04-Feb-15 11:24 by...
Forum Posts
Hi all, I have an old 871W that i am using to learn on. Having an issue where I can connect to the wifi but get no internet. I'm assuming NAT is the issue but it could be something else. If you could point me in the right direction, I would appreciat...
When I connect my PC directly with my Router (peer to peer), I get a speed of upto 39 Mbps which is the service provider plan I subscribed. However, when the PC is connect to a WiFi network hosted by the same router, the speed drops to 25 Mbps. Cisco...
hi, i am electrical student. i was given the semester project of making a network of two servers each having 8 users using 2 switches for each of them. the connect them with router. Servers' ip was to be given statically and then server would dynamic...
This topic is a chance to clarify your questions about the configuration, verification, troubleshooting and general best current practices of dynamic routing protocols. All questions regarding to general design, flooding, in-depth mechanics, and feat...
Alright guys, I've been scratching my head about this one for a few weeks and I'm hoping I'm just making a simple PBR mistake and someone can help me out. As you can see (hopefully) all the traffic from my home network goes through my ASA. That's al...
Hello,I have put together a small testlab for educational purposes containing:Cisco 877/878/800As.These are soho routers with the ethernet being non manageable which means all the Fastethernet0-4 ports cannot have IP addresses and you can only set ve...
Hi, I try to access the web server from PC1 for an http page.I can ping my default gateway, the dns server, all routers also router INT that is behind NAT.Vlan's, routing and NAT seem ok to me. Thanks if anyone can help me.
Hi expert I would like to know what is the difference between Shared Port Adapters and line card? Why Cisco name it difference?
Resolved! >paosti<ts bgp?
whati is bgp postit mean RP/0/0/CPU0:router# show bgp neighbors nsr standbyBGP neighbor is 2.2.2.2BGP state = Established, up for 5d04hNSR state = NSR Ready>>>>Outstanding Postit<<<s: 0BGP neighbor is 10.0.101.5BGP state = Established, up for 05:19:...
Hi, I am currently creating a lab of SD-WAN but having a hard time to connect all these devices. My concern is that the eth1 is not going up even i use the no shutdown command. Please guide me if I am doing it wrongly.
Hi,I Already got a great help to decide me buy the SG350 switch in this topic:https://community.cisco.com/t5/switching/help-before-buying-cisco-sg350-series-switch/m-p/3909676/highlight/true#M471315 The uncertain question is to definitely confirm, fr...
Dear team,i have cisco 2900 series router and i have a sucessfully configured NAT which routes all my internal users from the 10.*.*.*.* private LAN address to the internet. i have one public IP. The NAT is confiugred the usual way. NOW, What I want ...
I want to make redundancy in my company DC. Existing design was like this,Access Switch >> Core Switch >> Core Router >> ISPNo redundancy , single point of failure.So we, planned to stack 2 core switches, and 2 Core router instead of one. But the thi...
Hey everyone, We recently moved and I brought my Cisco 881W with me. The new ISP requires PPPOE, so I stumbled through setup as I have never done it before. My situation is this. Some of my devices work great, others are slow, some don't work at all...
