I've not had much experience with access lists and from what I've researched you can screw things up rapidly if not done correctly. Which is why i'm here. I've been charged with creating an access to deny SSL to management ports for everything except...
Forum Posts
Hello experts, I am having below config on my HUB and spoke routers: HUB1:interface Tunnel5656bandwidth 40000ip address 10.13.198.4 255.255.255.0no ip redirectsno ip next-hop-self eigrp 1no ip split-horizon eigrp 1ip nhrp authentication HA18BJ56ip nh...
Resolved! configure 4k as ntp server
hi,I would like to configure 2 of my 4k routers as ntp servers for my private network.I have also 5 NTP GPS where my 4k routers are synchronised on.So the "sh ntp ass" on 4k routers tells me ref clock GPS and strate 1 on 5 lines.To configure my both ...
Resolved! Route path prority
Hi, Guys,I have a question on route path priority scenario:Two hosts with public IPs and private IPs in two separate sites, such as:1. Site A has a host with public IP 202.202.202.2/32 and NAT private IP = 192.168.10.2/322. Site B has a host with pub...
Hi team, I am using 192.168.128.0/20 subnet for my network. I am dividing this network as VLSM concept, as attached document, i am using two cisco sg550 switches, in this switch i have configured four vlans, but i in real switch i am unable to ...
Resolved! RV345p vlans and static routes
Hello, Having some problems creating a static route between 2 vlans. I have the following vlans, vlan1 is default and vlan100 is for ipcams. (ignore lag8, it's a trunk to a switch)The goal is that I can access the ip cams on vlan100 from devices on v...
Hi, In the vManage apidocs, apis are arranged with reference to resource collection. And permission for the apis will be enabled with the reference to feature selection. Would like to understand for a specific feature, what are all the available APIs...
We are using cisco meraki mx100 firewall in school. We are encountering internet interruptions from all clients. The mx100 firewall seems to stop working for some times that we have to turn it off for a while then turn it on again to reconnect to res...
Hi ,i would like to configure on a pair of Cisco 7609 PE routers two L3 SVI interfaces on the same subnet but in different vrf; Is it possible to create such architecture (see attachment)?
we have migration plan on going for your datacenter location our company used to be ISP and we've got to block of subnet x.x.0.0/19 and x.x.224.0/19 we used to advertise this to block to our service provider from the BGP with network statement networ...
I am new to networking and learning most everything through some classes, books, Internet forums and trial & error on my part (I figure a hands on approach is the best method). My current problem is that I am unable to get my ISR-931 to route traffi...
I am trying to use EEM to send a HTTP request based on an event (I am just trying with a copy http://xxx null:). I have the guts of this working (i.e. the event happens and the action is triggered etc) however the URL is quite long - it is 103 chara...
Hi just looking for some opinion on a subject for research purpose. Is there any advantage of sharing load across multiple links if using a single link won't result in congestion. I have carried out test using a traffic generator and i have sent 100...
Hi, IP header has two fields IHL and Total length. Below is the reason I found for having both these fields instead of one. "The Total Length field is required in the header because some lower-layer protocols that carry IPv4 datagrams do not(accura...
When configuring a route-map with the "next-hop dynamic dhcp" option, the dhcp gateway remained UNKNOWN until we rebooted the router. This makes sense since there is no mechanism to generate a dhcprequest for a gateway until the router is rebooted. ...
