Hello,I've installed c5921 on a small Intel atom based device. I've configured the router with two DHCP service ports. I plugged a Linux server into one, and a laptop into the other. Running ethtool on both ports shows the negotiated speed of "100...
I have an issues with using the loopback as source for syslog packets.The second the loopback is used logs are not making iy anymore to the syslog server. Everything works using the Gig interface.The syslog server can reach the loopback and the route...
how can i configure the network so that left hand side network can access to web server and able to ping the right hand side network, and network right hand side network only can access to the web server but not able to ping left hand side network
Will they ping (image is attached). In my case it's not pinging.And if pinging, how?Ps : Using C7200(router) ios image in GNS3
Hi , I am working with few customers who are terribly dissatisfied with the lack of ability on Cisco ISR c1111-8p routers to do the following: >Direct internet breakout (which is supported through local-tloc function on vEdges but not available in cE...
We would like to establish a site-to-site connection, enabling Layer2 traffic (especially Multicast) flowing between our two sites using two of our ASR1001-X routers.I've already read in an other discussion that L2TPv3 should support this. Would this...
client=====[router1]====[router2]====[router3]=====[router4-gre/tunnel ]===[gre/tunnel router5]===server What is the best way to troubleshoot/identify which router in this path is blocking a udp response from the server to the client? I am able to ge...
Dear All, When I use the show interface command on the Cisco Router ISR-4331, it will display as below information. The word that I mark red, it refresh every 5 seconds. But, I compare with the old router model like a Cisco 29XX or 28XX, it can be re...
I am attempting to stand up a multi-tenant configuration in my lab. I have created the vContainer server with a 20G second drive, loaded the viptela-smart-18.3.7-genericx86-64_vhd.tar.gz image into the admin home directory. When I issue the request...
Hi all - I’m doing an implementation of Cisco SD-WAN (Viptela) - around 90 routers (mix of ISR 1111 and ISR 4k)- The problem is - this is a pure on-prem deployment. So, the routers won’t get an internet connection- Everything will be mpls- Since the ...
I currently have an ASA in production and have a question about setting it up in Active Passive failover. I've got a 2nd unit that is the same with same firmware and everything. If I want to setup the passive unit will it cause downtime? My current u...
Hi,So I have a brand new (bought about 2-3 months ago) ISR4331-SEC/K9 running 15.something.something and I have just started booting it. I would like to enable the WebUI which I hope is similar to an SG350 WebUI where I can actually configure everyth...
What is the MTBF for the Cisco 2M-2GE-SFP-CU Service Module? I don't see it listed in the data sheet.
Hello! We are facing problems while applying shape policies in our GRE tunnels. 1st problem: It lets you remove a policy from a interface, but when you try to reenter same line it accepts the command but doesn't apply: E.g: ASR1K_DG_RTR_I#sh run int...
I'm setting up 2 ASA's in failover mode (active and passive) g0/0 is my wan (public IP)g0/1 is my lan (local IP)g0/5 is the lan failover (local IP) Do I need a secondary IP on all of those interfaces or just on the lan failover? Also for the state f...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM | ||
| 02-04-2026 09:44 PM |
