I am trying to setup a config where i can have both my wired (primary) and Cellular (backup) connection in a active/passive setup to where is the wired connection drops it will swing over to the cellular then back to wired when wired is back up. righ...
Hi there! So we are trying to setup the ISR-1100 Router via a VPN to our "corenet" one route via Cabel and one the other route the 4G LTE network. We can get the traficc to work from Int gi0/0/0.903 - 10.240.2.238 to the Checkpoint Firewall 10.240....
Hi ,Strange situation on 3925 , there is no 85Mbps traffic on the router and message apears .%CERM-4-TX_BW_LIMIT: Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license.*Oct 24 11:02:59.6...
Hi, We have quoted the following option while quoting the ASR9001 in order to get the MPLS features: "XR-A9K-PX-06-01" (Cisco IOS XR/MPLS Core Software). But while configuring the MPLS we are unable to configure "mpls ldp". Kindly help me to get the...
I have modem router and i configur with static IPs : 41.38.100.218 to 41.38.100.222Subnet mask : 255.255.255.0Getway : 41.38.100.217And i have another's line adsl on the same router but dynamic configurationI need all step on router 1841I'm close DHC...
Hi,I read here in Cisco website that in order to redistribute routes from one protocol to EIGRP, it should have a default-metric set or a metric set for the routing protocol. If there's no metric set then the route will not be redistributed.Im wonder...
Hello everyone, its my first post so sorry if i make some mistake. I have a big doubt about AS and BGP, i have ASN 263916 in on premise site with IP Address 200.9.144/24 and my question is. Its would be possible use the same ASN number and same publi...
I'm rusty with QoS. Really haven't had to work with it much since a lot of the networks I work on have bandwidth to spare. I've been working with some MPLS sites that have lower bandwidth connections, around 10Mbps is typical for these sites. There h...
Hi everyonei recently got an 887 adsl router to be added for internet.... hoping the configuration should be the same as 877 i have done the following configs...interface ATM0no ip addressno atm ilmi-keepalive!interface ATM0.1 point-to-pointpvc 8/35 ...
Hi,Can anyone help me validate this cause of this log below.I am trying to install a backup ipsec tunnel using dialer and i have been having this issue. Basically, the dialer interface config i used is the same with other sites, the only difference w...
Hi, is there a list of alarms and corresponding severity for ASR 903?What I need is which alarm trigger critical severity alarm, or which one trigger Minor or Major and so one.
Ok so i have one ASR (ASR1) that have 10GEupgradelicense and other features using traditional licenseing way. another ASR (ASR2) have smart licensing method and have 24 1G-4 10G temporary license. I have requset from licening team to re host 10GEupg...
Cisco 877W router and external ADSL modemIn order to support ADSL2+ on a pre ADSL2+ router and in preparation for a later migration to BT infinity I am trying to configure the Router using an external adsl2+ modem appropriately.The original configura...
Hello all, We are trying to create a QoS policy to prioritize EIGRP traffic across an L2 WAN link. We are theorizing that the link is getting saturated, dropping EIGRP packets and thus dropping routes. This is the police we have came up with and wa...
I have confusion in finding the bandwidth for an interface, between the bolded values below...BW 1000000 Kbit or 100Mb/sAlso, what is the difference between them? Router#sh int g0/1GigabitEthernet0/1 is up, line protocol is up (connected)Hardware is...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM | ||
| 02-04-2026 09:44 PM |
