I am trying to setup PBR to route traffic from a certain subnet, going to certain IP ranges, over two different next-hops.source subnet (vlan151, VDI clients): 10.1.1.0/24destination 1: 172.16.0.0/24 (and others but left out for simplification, the i...
Forum Posts
Hi AllI cant get the dialler interface di0 to come up and get an IP address with the carrier. I'm using bits of a working config from an IR809. The only difference is that that router is working with encapsulation slip but the 1941 doesnt support sli...
Most have seen the message: (config-pmap-c)#shape average ?<8000-1000000000> Target Bit Rate (bits per second), the value needs to be multiple of 8000percent % of interface bandwidth for Committed information rate My question is why does the router c...
Hello! I Bought a used 1841 Cisco Router from Ebay.However, the previous owner forgot/did not remove the configurations and still has a username/password security Is there anyway to remove/reset the security?The first thing the command prompt is re...
Hi, I am trying to Nat a network 10.1.1.0/24 to another network 192.168.1.0/24. When this happens, the last octets Z should remains (e.g 10.1.1.50 to 192.168.1.50), otherwise packets will be lost. Basically it's a 1-to-1 NAT. May i know whts the step...
Resolved! DF bit and route map
Hi All,i have issue with Switch Ports Model SW Version SW Image Mode------ ----- ----- ---------- ---------- ----* 1 56 WS-C3850-48P 03.07.04E cat3k_caa-universalk9 INSTALL when i add:interface Vlan261ip address 10.158.20.126 255.255.255.128ip policy...
Resolved! Static routing with 5 routers
Hello everyone. I need to help with static routing on this type of network with 5 routers. I need to ping from one to pc to another. (PC0 -> PC1 and PC1 -> PC0). I understand how to do static routing when I have simple network with two routers but th...
I needed to test dual ISP configuration on a firewall, I was able to setup a quick lab with a set of Cisco 2901 ISR to test the fail over scenario. This got me to thinking could I also test VPN but how do I route traffic once I go past the WAN interf...
Hi experts, we are using cisco 3850 (layer 3 switch) to connect to isp and then connecting it to aruba controller for access points. Now customer wants to add 1 more secondary ISP as a backup so if main ISP is down the secondary ISP should start work...
Hello. I always thought that there is at least two different NAT with different order of operationsClassic NAT (ip nat inside, ip nat outside, ip nat inside source...). If packet is going from inside to outside there is routing first, than NAT second...
I passed exam CCNP router and trouble shootingaround 12/28/15 but i do not still pass switch..I Know router and trouble shooting exam expire in 2018but I passed CCDA and OCSE around 2017..And then my CCNA was extend in 2020I hope router and trouble s...
Hi Team, Need to not send/receive anything from particular ISP BGP neighbour we have 2 internet circuits already and considering the capacity in future , we are adding the 3rd circuit but just we wanted to activate the 3rd circuit and need to monito...
Hi All, All devices within both subnets are reachable across both subnets but each subnet can only reach it's own interface gateway, we require to have reachable gateways across subnets. For example;1) subnet-1 can reach subnet-1 gateway but is unabl...
Have a BGP routing/advertising question involving implementation of multiple default routes via BGP without getting the ISP involved in metrics. ISP is providing MPLS for Full mesh between all remotes sites, Data Center, and Corporate HQ site. I hav...
Resolved! DSL QOS - Supplier information
I know there is plenty of information regarding QOS already in the community however, I would like to know the design steps before the actual configuration to ensure I am not forgetting a step. We have 887ISR on DSL and we have some voip handsets at...
