hello to all forum members. I have a question regarding the matching of the connection between the AT-2746FX / ST / ST network card and the CISCO WS-C2960C-8PC-L router by optical fiber connection. G-BIC, GLC-FG-100FX does not work as the producer wr...
Forum Posts
Resolved! iBGP design problem
Hey Guys R1 and R3 are edge routers and have iBGP together. They have eBGP with R5. Link 1 is primary and if it goes down traffic which enters R3 should route to R1 and then to R5. Here is the problem. If I dont include R2 in iBGP, then it will not k...
Hi, I have a switch at a site and I need to copy IOS from the FTP server, but the FTP server's IP is not pinging from the switch. Can anyone help me what needs to be done to copy the IOS from FTP to the switch or is there any other way (like copying ...
Hi All I am setting up a branch site on my IWAN, APIC has deployed the config. I have had to add some config for the Internet access as described in the Cisco CVD for DIA, this is because the outside interface sits in a front door VRF for the vpn tun...
Hello, I have a CISCO1921 router. The interface G0/0 is connected to a WAN modem dedicated for a layer 2 site to site connection. The connectivity to remote site (172.20.90.2/24) occasionally goes down. Below is the interface config and statistics. A...
Hello, today I've got a Cisco 2801 that I'm trying to factory reset but I can't because "Password Recovery Functionality is Disabled" I've already tried and followed various guides and threads here on Cisco Support Community but I can't in any ways i...
Resolved! BGP Routing policy behaviour
Hi All, I am reviewing some configuration on one of our routers and confused by this design: router bgp 12345 neighbor 1.2.3.4 remote-as 6789 neighbor 1.2.3.4 neighbor 1.2.3.4 send-community neighbor 1.2.3.4 remove-private-as neighbor 1.2.3.4 pre...
Hi All We have a main HQ MPLS router with 30 sites hanging off it, we have a policy map applied to the outbound direction of the WAN interface. As we have traffic coming in from the sites where some QOS is not configured, do we need to apply a policy...
Hi experts, I would like to create an access-list and use it for vty line. The purpose is allow ssh traffic for only specific subnet and host. I have created one as below. configure terminal ip access-list extended ABC permit tcp 10.0.0.0 0.0.0.2...
Hi Master,I quite confuse with the values behind the ip prefix list. Can some1 make me understood ?For example : ip prefix-list A permit 10.18.0.0/21 ge 24 le 24
Hi, I am trying to run GLBP over IPv6 between two Cisco 4451X ISRs however when i attempt to set up the group on an interface there is no option for ipv6 only ip. For example when I attempt to run glbp [group number] ipv6 [ip address] there is no i...
Hello team, I'm in an RFP and they are asking for VRRP-E, which is an enhanced version of VRRP. "The most important difference between VRRP and VRRP-E is that all VRRP-E routers are Backup routers; there is no Owner router. VRRP-E overcomes the limit...
Resolved! Show CDP neighbors of all switches
Is anyone aware of a way that I can easily execute and gather the results of a 'show cdp neighbor' command on 100 switches? Thanks, Aaron
Hi All , I Would like to know how to confirm if I can upgrade my Cisco 5525's to use IPS SOFTWARE. I am running around in circle trying to find out . Cisco says yes if I have k9 ips but I dont know if I do . See below output . ardware: ASA...
Hi, if I have already configured something like the below for my port-adaptor cards - card type e3 2 0 card type e1 2 2 card type e3 3 0 controller E1 2/2/0 channel-group 1 timeslot 1 .............................................. If one or mo...
