I know routers often rate limit the generation of ICMP error message to keep CPU load manageable. Does anyone know if there are routers that also rate limit the forwarding of ICMP messages? In particular, I'd be interested in Cisco routers.The reason...
Forum Posts
Resolved! vPC on Nexus 9000
Is't ok on nexus 9000 i want to add command fast-convergence on vpc peer, also vpc peer has delay restore and auto-recovery, read some article fast-convergence heplfull vpc domain 1delay restore 150auto-recoveryfast-convergenceReduced recovery time ...
I have typed below command, normally it has to let me enter yes or no but in mobaxterm when i press enter it is jumping to next line R1#, skipping Reset ALL OSPF processes? [no]:anyone faced this? pls help. R1#clear ip ospf processReset ALL OSPF pr...
Hello, We are dealing with a strange issue about Syslog Logging for the NGFW Policy configuration on vManage 20.15+. Usually until 20.12.5 using UX1.0 we where able to configure Syslog settings for the policy on the Additional Settings. On 20.15+ usi...
IN-TN_CHN_BNG-INFONET# show interfaces po10 human-readablePort-channel10 is up, line protocol is upHardware is 10GEChannel, address is 5c5a.c700.8ec9 (bia 5c5a.c700.8ec9)Description: ## CONNECT-TO-INTERNET ROUTER ##Internet address is X.X.X.X/XMTU 92...
I am trying to connect a PT router to a WRT300N wireless router with a crossover cable or straight through. I want the PT router to be the gateway. I have the WRT300N router set up and connected to 2 PCs using WPA2 personal encryption.I am not sure h...
Hi, I know that Cisco Edge 340 is a retired product. If anyobe can provide ISO file I can try recovery for Media Player as it displays Error in Hardware validation. Regards, SA
Resolved! NAT Translation not working on IOS XE 17
I have situation which I apparently do not understand. NAT Translations show 0 in following case:show ip nat translations Total number of translations: 0nat-limit statistics:max entry: max allowed 0, used 0, missed 0longest chain in local hash: 0, av...
Hi! I have a problem with VRF NAT translations.We have a cisco 1111 router with following configuration:ip vrf WILDNETip vrf WILDNET_PTip vrf WILDNET_TMinterface GigabitEthernet0/0/0description outsideip vrf forwarding WILDNETip address 1.1.1.10 255....
I am trying to install c1117 router and soda on it ,I need help to install
hellowe have an SDWAN DIA deployment in production the current configuration uses Traffic Policy with a Data Prefix of allowed target public IPQ is there an easier way to control DIA traffic ?I would like to use some of the Features below URL filter...
We bumped into problem with wake on lan on devices c1111x / c8200. WOL works correctly some times (during we have arp) after arp dissapers (or if I clear it) WOL doesn't work.Gi0/0/1.1 - WAN uplink sdwan tunnelGi0/0/0.200 - devices with network 192.1...
I have a project here for a simple network in Cisco Packet Tracer. All connections respond when pinged, but the laptop connected wirelessly with the WRT300N router cannot be pinged from outside the network. The laptop itself can ping any other device...
My inside trunked router port randomly shuts, with no indication of why in the logs. I had debug STP. What's another debug I can enable to try and get an idea why?Router Log Dec 3 2025 01:26:37 UTC: %TRACK-6-STATE: 22 interface Gi0/0/1.2 ip routing U...
So, I am dealing with PLC one one side...10/100mbps port. Via a single mode Fibre cable it is extended to the switch cabinet. I am suppose to select the Switch & SFP. Can someone with experience validate the selection that I derived as : Cisco GLC-FE...
