hellloi have cisco router 860 andit has two networks: WAN 132.66.x.xLAN 10.10.10.xVLAN1 10.10.10.10 also DHCP every time i want to connect to the PC on the network 10.10.10.x via SSH on Router i want to make a tunnel using port 2222. for example i ...
Forum Posts
We are using Cisco 2921 routers and have to connect Vlans to DMZ server and to ISP. We have done vlan interconnectivity using router at Access layer. Now we have to use router firewall between DMZ, internal Network. We have to connect to ISP and DMZ ...
Hello,after a recovery of a main power failure the RPS LED on my Cisco 2960 is blinking amber.The command sh env power on the Switch tells me: POWER is faulty.sh env rps says: RPS is supplying.On the RPS2300 the DC output LED is blinking green.Due to...
Hey all, hoping you can help as I am pretty new to router config. Ok, so last week switched one of our sub offices from adsl to vdsl and swapped out the old 887 router (which establishes a vpn connection back to head office) with a new one and the en...
Im aware that a customer using a L2VPN may send traffic over to a PE which is encapsulated as Null port, 802.1q port or Q-in-Q port type. I think Null encapsulation translates as raw mode / port based VLAN (?) and requires service provider to send ...
Resolved! Serial tunneling
Hi all,I'm looking for help in configuring CISCO environment.... usually rookie question We have two routers ( 2600 series, IOS 12.0(7)T ), E1 connected via PRI 2CE1U interface on both sides. The routers are equipped with WIC-2T serial interface car...
Resolved! Interface config for ISR Router
Hi Experts, Recently I have purchased a Cisco 2921/K9 ISR router with UCS Server Module which I will use to install CUCM & CUC. However, I have a bit confused on the interface connection. Below is the config guide provided by my senior. Let's called ...
Resolved! How to know the type of BGP
Hello, I am trying to figure out which is the type of BGP of my peer. I would like to know how differenciate if is eBGP or confederation type.
Hi; I setup ipv6 tunnel (he.net) and try update dynamic ip with below conf ip ddns update method he-update HTTP add https://username:password@ipv4.tunnelbroker.net/nic/update?hostname=hostname interval maximum 0 0 1 0 ! interface Dialer0 ip...
Hi, struggling to see at what stage TCP fits into the overall BGP state process. I know it's the first thing that happens, but does it come before Idle or before Active for example or does it function alongside these and how? In essence, where does...
Hello everyone! Where can i read about cisco hardware architecture for specific platforms(6500, 7600, asr1k, asr9k, etc...). I want to know that is RSP, RP, SP, ESP, DFC, MSFC, CFC, etc... Are there any cisco press books about it?
Hi I have a router where the same ACL is applied across several interfaces. I would like to know the ACL counts/matches for each individual interface. Is this possible? I don't believe it is but would appreciate your views. Look forward to h...
On cisco´s Website, there is a picture of an IP NGN Carrier Ethernet in:http://www.cisco.com/web/BR/solucoes/sp/network_infrastructure/carrier_ethernet.html#How does it work? I mean, since the Multiservice Core, the Intelligent Edge, Carrier Etherne...
I'm using Named EIGRP and i need to redistribute from an AS to another but I´m not getting the redistribution done!. For this example I have the network 10.10.6.0 on AS 1 VRF GRE and need the route to be redistributed to AS 110 VRF MPLS. What i'm m...
Resolved! SG-200 08 ntp not working
Hi there, i bought this Switch but ntp is not working.All other Clients behind the Switch do have no Problem getting Time from my local ntp Server(192.168.1.1). Active Server is always 0.0.0.0.. I tried with sntp broadcast and unicast. I tried it wi...
