Hi I have a router where the same ACL is applied across several interfaces. I would like to know the ACL counts/matches for each individual interface. Is this possible? I don't believe it is but would appreciate your views. Look forward to h...
Hi I have a router where the same ACL is applied across several interfaces. I would like to know the ACL counts/matches for each individual interface. Is this possible? I don't believe it is but would appreciate your views. Look forward to h...
On cisco´s Website, there is a picture of an IP NGN Carrier Ethernet in:http://www.cisco.com/web/BR/solucoes/sp/network_infrastructure/carrier_ethernet.html#How does it work? I mean, since the Multiservice Core, the Intelligent Edge, Carrier Etherne...
I'm using Named EIGRP and i need to redistribute from an AS to another but I´m not getting the redistribution done!. For this example I have the network 10.10.6.0 on AS 1 VRF GRE and need the route to be redistributed to AS 110 VRF MPLS. What i'm m...
Hi there, i bought this Switch but ntp is not working.All other Clients behind the Switch do have no Problem getting Time from my local ntp Server(192.168.1.1). Active Server is always 0.0.0.0.. I tried with sntp broadcast and unicast. I tried it wi...
Hi! I am working on creating template for 2960x lan base and wanted to put some feelers out there to get some thoughts. From my understanding that it's best practice to put the mls qos trust cos on the end user access switchport that is configured f...
I have a Cisco Integrated Service Router 3825. It has three physical interfaces(GigbitEthernet0/0, GigbitEthernet0/1 and one SFP ), I would like to use three interfaces at the same time as a firewall to build three zones(Inside, DMZ and Internet) eac...
VRRP not forming between SRX and Cisco on MD5/Key-string/Key Chain. Any thoughts? IOS - c2900-universalk9-mz.SSA.155-3.M1.bin Junos: 15.1X49-D100.6JUNOS Software Release [15.1X49-D100.6] no key chain VRRP!key 0!key-string TEST!interface GigabitEthern...
Hello,I have stack of 2 switches 3750x. I want protect the stack's CPU from pinging. I have next settings:class-map match-any ICMP_PORT_TE_1_1_2match input-interface TenGigabitEthernet1/1/2The TenGigabitEthernet1/1/2 is uplink. class-map match-all IC...
I am currently a 4th-year student in PTIT, majoring in telecommunications network Currently I am preparing to do the project but still do not know the direction of how Hope people can give some ideas for your projectCurrently, I am preparing to do th...
An IPv6 tunnel (Hurricane Electric) has been in place and working for years. US resident endpoint devices looking to connect to NETFLIX are routed to the IPv6 address where NETFLIX denies access to content since NETFLIX cannot determine if the endpoi...
I've set up multiple routers over the years by a handful of companies. If there was ever a problem, typically there was always as solution to be found on the internet. Never have I had so much trouble with a router that I've been forced to register o...
Hi, i have open some ports on the router before and without problems, but when im doing it now, the setting is not showing upp in show conf, im typing this command: ip nat inside source static tcp 10.0.0.8 7563 interface cell0 7563 Here is my con...
Hi, I have 2 subnetworks and I want to seperate them so that they cannot communicate with each other. Below is how I have tried to do it but, it doesn't work as when I attempt to ping from one to another it still goes through. Am I missing something?...
I have an urgent problem with the Cisco aironet AIR-AP1852I-E-K9C the problem is: The access point has two SSIDs 1- SSID for Employee 2- SSID for Guest The firste SSID works without any problems But the second one works only with mobile phones ...
I have a router that has a vam2+ VPN module running DMVPN on VTI interfaces doing about 180 Mbs of aggregated VPN traffic. When doing a show proc cpu sorted it shows something like this, CPU utilization for five seconds: 72%/69%; one minute: 75%; f...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-09-2026 09:36 AM | ||
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM |