Hi, I currently have 2 cisco 3750X stacked switches and I need to replace them with 2 new cisco 3850 switches. What is the easiest way to accomplish this? I thought of configuring the 3850 stack with basics, then connect to the 3750 to pass vlans....
I have two sites linked with a basic IPSEC tunnel between them. I am struggling to get any more than 10MB across the VPN. Site 1 has a 50MB LL and site 2 Is in a Data Centre with a 1GB Max connection. Both routers are Cisco 1841 routers with VPN card...
Hi All , Could you all let me know what is Recursive Lookup. I just want to know it without any regards to any protocol. As per my understanding : Routing table for R2: C - 10.0.0.0/24 -> S3C - 10.0.1.0/24 -> S2C - 10.0.2.0/24 -> S0C - 10.0...
Hi, I would know what happen after the eval right to use was end. Cisco license activation for example c2900 security feature Thanks Erico
Dear, We face problem in our network, NAT translation failed and we don't have internet access when this problem occure. How we can fix this issue. Running Configs and Logs here, Interface and Nat Configurations, interface GigabitEthernet0/0.1659 d...
Does someone verifed Luc De Ghein's assertion below ? If a prefix is reachable via a mix of labeled and unlabeled (IP) paths, Cisco IOS does not consider the unlabeled paths for load-balancing labeled packets. (page 50, MPLS Fundamentals, Cisco Pre...
Does any one knows the major benifit and disadvantages of IE 2000 vs IE 4000. i am thinking about deploying one of these devices in bus stops for IP connectivity.
Hi, i need to ask is EEM Applets are recommended to use and regularly used in networks? Like i used it once and experience was bad that, my Router kept crashing as soon event generated, so i never worked on it since then. But now i have some requirem...
Hello, I have Cisco 2811 router that is not responding to any command given in Rom Monitor. Even 'help' command is not returning the list of available commands: rommon 1 > confreg 0x2102 monitor: command "confreg" not found rommon 2 > ? monitor: comm...
Hi, will the 887VAM 897VAM adsl annex-m router also sync on a standard annex-a line ? (qould like to know it before buying...) i found a command to set the mode in ios but do not know wether the electronic supports that. Thank you for your help, Juer...
ASA 5505, 9.1.4 I few days ago I noticed continual activity on my WAN interface light. It's definitely coming from the outside as my cable modem activity light is also blinking consistently. This has happened previously with brute force attacks on my...
Hello, I'm facing problem with ipv4 address. I have configured a list of address on bgp but few ip pool not showing mask, even though I have configure. Below are the output. network 192.232.131.0 mask 255.255.255.0network 192.245.196.0 mask 255...
Dear All, Our equipment Cisco 7609-S today detected numbers of packets to ips not exist in routing table and punted to cpu which caused high cpu loading. Could you please advise if there any solution and how we can prevent such situation happen?As...
Hi everyone, I have the following topology with extended layer 2. i have all router with the same metric so all the router have two path to same destination. but what happen if the link between the two switch layer 2 goes down. all the router send ro...
Hi, Can anyone pls explain me the difference between a Router & a layer 3 switch.Also why do we require a router when layer 3 switch performs routing ? pls explain in detail...Regds,oratecorp
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM | ||
| 02-04-2026 09:44 PM |
