HiHoping someone can help. I recently purchased a NIM-VAB-A card to go in our ISR4451, with the goal of eliminating an ISP's insecure unmanaged router. I have configured this following various guides online, and it is working from a connectivity poi...
Forum Posts
Resolved! MX to cloud
Currently have a global Meraki infrastructure want to begin to explore NGFW (?). The goal is our reduce the hardware footprint on premise. We're a global firm and want to begin in our US offices.What are the major factors to consider? Is there a Mera...
Can a VLAN being extended via VXLAN between data-centers have multiple IP address ranges?Example of VLAN to be extended:interface Vlan20description DATAip address 10.84.20.1/24ip address 10.91.20.1/24 secondaryip address 10.202.20.1/24 secondary
Hi, EveryoneHas anyone seen this log into the Cisco ASR 901 router:pstorm_bcm_prog_tunnel_push_1:2032: MPLS Tunnel index crossed maximum limit. l3intf=740, Err: -6, Label= 306. primary pathBest regards
Hello Fellows, I'm trying to find if there is any Cisco authored or reputable sources for recommended practice when it comes to scanning interfaces on Cisco routers. Our vulnerability management teams insist on them being able to scan all interfaces,...
Resolved! Cisco EEM script to bounce an interface
We have about 120 DMVPN spokes and a few more remote ones occasionally lose DMVPN to the HUB site. A quick bounce of the tunnel normally resolves the issue.I have been trying to get an EEM script to do this for me. I applied the config, clear the log...
So I'm at a bit of a loss with this one. I've already configured it and had it working before, but decided to restart for fun. I typed up all of my actions beforehand, made some shoddy IP addressing tables in Word, and figured that was that. I go bac...
Resolved! sdwan edge where is startup config
I'm interesting whrere is startup config in cedge?
Hello,so we work in our DWDM network using NCS 2002 & NCS 2006 and there are aggregation sites on it. we want to perform fail over test on the network. i'm a little bit confused in the procedure to be followed and also i can't find detailed alarm tro...
Looking for recommendations for routing traffic from ASA back to router on "inside" network so we do not have to add static routes on systems. We recently added an ASR1001 to our "inside" network that routes traffic to Amazon thru a Megaport link tha...
Hi Guys, Not sure if in the right group here, but I've been upgrading old 2811 with ISR4331's, this one solution runs HSRP on the client facing side with matching static NAT entries, no problem till i upgraded both routers, currently had to roll ba...
Hi,Have a great day!I'm Heshan Yasas Kavinda and I am studying CCNA, I Have a CISCO 1905 k9 Router with an EHWIC 4ESG 4 Port Card.when I assign their IP address for the port it says "% IP addresses may not be configured on L2 links."TesTR1#show ip In...
Referring to campus networks where direct fiber connectivity exists between routers and CORE but the network is too large/complex for a collapsed-core scenario thus entailing the need for an IGP. A non-Cisco SE came in to sell us a VXLAN solution for...
Hi. We had weird problem. - vManage, vSmart, vBond : 20.9.4 (Manage 20.9.4.1) - C1111-4P SD-WAN Mode : 17.9.4a Only 3 traffic go to SIG by traffic policy (O365, Webex, Windows Update) But one of our custom application which was defined as a inter...
Hi GuysI remember seeing a good post and diagram how a loop caused by mutual redistribution between 2 routing protocols was caused and mitigated, had anyone got a good example of this with a diagram? I think it was stopped using tags or distribute li...
