Hi All I did not type the following command. Why does it appear when I show run ? Which command can cause the issue? Thank you mac-address-table static 0000.0c07.ac01 interface FastEthernet1/0 vlan 3
I am having issues with BGP seeing the advertised routes. I am trying to find an alternate to AS-Path prepend and trying to use bgp instead for a redundant path. Setup:-We have 3 mpls sites. (in reality its more than 20 but for simplicity we will cal...
Hello! I hope this isn't a thoroughly newbie-like question, but I wasn't able to find an obvious, clear answer in the usual documentation and resources.The scenario is as follows: two routers peering via eBGP; router A has a more generic /28 route vi...
Dear Team,Have some issue with the followingWe are facing some issues, likewe can’t access some internet sites , which have IP addresses in the range of 172 “as same as our private network”,need some help in specifying the internal range to be only...
Dear AllHere is a question. Please see diagram in attachment. Router 1 is connected to Router 2 with two connections. MPLS is primary connection and DSL VPN internet is backup connection for the primary connection. My purpose is that DSL VPN will be...
I have to do NAT overload on router. Following is the config, and as long as I source traffic from router interface it will work.. but when traffic is across G0/0 (inside) it will not hit ACL or translate There is no host alive at 10.91.8.1 yet and...
How to configure NAT load-balancing over two ISPs on Cisco 2851.System image file is "flash:c2800nm-adventerprisek9-mz.151-4.M.bin"My config (users behind the router/PAT unable to acccess to Internet, I don't known why?!!): interface FastEthernet0/1/...
Is someone has experience with cisco 4331 with SM-X cardIf I have LAN base image for SM-X card and base image for 4331 router - Can I configure SVI interfaces on the router and then place particular L2 vlan to access one of the port on the SM-X card...
I have a question similar to another asked in this forum but have never found or seen an answer. Thank you in advance for any assistance you can provide. I have a Cisco 7301 that I need to use as a gateway to my private SIP network. I have configu...
For Cisco 2921, which module is the correct one if I have 2x E1 handoff from provider for data-only MLPPP? If I don't need voice, would I still need to buy a uc license to use the VWIC3?VWIC3-2MFT-T1/E1HWIC-2CE1T1-PRI Thanks.
My quick question is does the Cisco 3560 Compact switch support dot1q tunneling?Ordinarily I would have used a 3560 8 port switch, but having trouble getting hold of these, so looking for an alternative model to replace them.The data sheet and releas...
Hello Gents , can i use different RD value for same VRF in different PE. what is the advantages and disadvantages. Thanks, AD
Hi , Recently i configure cisco881w Router, i am facing this problem , whenever i connected to the network, I am not able to resolve the DNS, i had tried to put in ip address of google in the browser, it works charm, but when i type in "www.google.c...
Good day,I have access-lists on my cisco router 2900 where some are attached to the crpypto maps for IPSec tunnels and one linked to the access-map o the line VTY.So now I need to allow access from two specific IP's to a specific IP and I want to blo...
We have a 7204VXR router with an NPE-G1 serving as our gateway router. We currently are connected to one ISP, one BGP peering session on which we receive a single default route, and another on which we receive a small table of Internet2 routes.Lately...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM | ||
| 02-04-2026 09:44 PM |
