How to get access for downloading Cisco IOS from Cisco Websites ??
How to get access for downloading Cisco IOS from Cisco Websites ??
We are trying to apply QoS on a Dialer interface. Every time we issue the command service-policy output upstream-policy - nothing happens and the config does not get applied. No error messages appear.QoS config:class-map match-any web-class match p...
Dear all, Hope you are doing well. I am searching information about the size of the input hardware buffer of a router interface, but I can't find anything. Could anybody tell me that value on a Cisco 3945 platform and a Cisco 2921 platform? Thank you...
Hello.I have four 2960 running 12.2(55)SE7.These switches stop responding at the console and vty but other functions are ok.When I try to connect I receive the banner and no more: no prompt.Any ideas?Regards.Andrea
Hello,i have a questionwhy bgp isnt supported on 5510-5520-5540 asa appliances?Because of hardware performance? Cause bgp is supported on 5505.Why we cant have any bgp support on these devices and we must change to new ones?I cant understand this...h...
Hello, I have a new 4500-x running IOS-XE version 03.03.00.XO RELEASE SOFTWARE (fc2)ROM: 15.1(1r)SG2.it has a dual supervisor and it is configured as a simple switch (all ports on the same VLAN) and if I connect two pc on any port and I start ping...
Hi.. I have configured service policy on tunnel interface but i am seeing packets are being drop in default class even if bandwidth is not full utilized.I have been running 20MB mpls circuit and configured GRE tunnel b/w two locations over mpls circu...
How to Download Cisco Operating Systems, and What is the procedure for doing that ???
Hi.I'm having problems reaching internal services over my site-to-site tunnel while they have a NAT configured. Description:On site A I have a MSR30 router and behind that I have a web server running sites on port 80 that I have made available exter...
Hello I have an ASR router with a WAN link of 100M. The LAN connection for this router is Gig capable.Should I configure the LAN interface on the router for Gig or would this cause problems with potentially 10 times the dataexiting the LAN out to the...
I have a 3925 with 4 Gig Integrated Interfaces and 2 SFP GI0/0 and GI0/1. Will I be able to use the SFP interfaces if the integrated GI0/0 and GI0/1 are being used? Thanks. Todd
Hello All, I need assistance trying to figure out what my VPN preshared group key is. The router is a Cisco 2811 router and need to set up a VPN client but I don't remember what the group key was. How do I get it from the CLI on the 2811? Thanks,
Hi All,With BGP communities, how would I go about ignoring the ASN portion of a BGP community and accept a wildcard value? For example, if any of my peers/transit providers that send me a route that is tagged with the community X:666 I'd like to rej...
Hello. I need some help please.I need to figure out how to set this up.We are trying top move from a current inefficent setup to a new solution. How can I connect 4 separate internet hand offs on 1 3850 switch?I have 2 ASA in a failover setup and a 3...
Hi Guys,Can somebody explain to me what is the following statement mean (which is a part of Cisco IS-IS documentation):"In MPLS VPN environments, reachability information for the loopback addresses of every Provider Edge (PE) router is needed. Leakin...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM | ||
| 02-04-2026 09:44 PM |