Pre-Checks Connect the console cable to the CIMC port, not the standard Console port (as shown in the diagram). Ensure that the Backbone is connected to the MGMT CIMC interface. Power cycle the device (turn it off and back on) before beginning t...
Forum Posts
Hello everyone,I’m currently dealing with an EtherChannel issue between a Cisco Catalyst 8500 (IOS XE) router and a non-Cisco switch.On the Catalyst side, the Port-Channel (channel-group 1) is configured as a static L3 EtherChannel, while on the swit...
Hi everyone, We’re running a dual-hub DMVPN (Phase 3) environment on Cisco ISR 4400 routers (IOS-XE 17.9.x).All spoke routers are dual-homed — each forms tunnels to both DC-A and DC-B hubs. Recently, several spokes lost their BGP peering with DC-A, w...
Resolved! Is SD-WAN with Azure worth it?
Hi all experts, I'm new with SD-WAN, I'm studying if compense migrate the current company onpremise networking infrastructure to SD-WAN or not. I see different advantages, but I'm not understand what Azure really contributes. Most of the network mana...
RP/0/RP0/CPU0:TEST-A#sh policy-map interface twentyFiveGigE 0/0/0/33Mon May 5 16:24:49.403 JSTTwentyFiveGigE0/0/0/33 input: IN-CORE-QOS-POLICYClass IN-CONTROL-SIGNALINGClassification statistics (packets/bytes) (rate - kbps)Matched : 92749145131/16572...
Translator Translator Translator My ISR 4331 is with the version isr4300-universalk9.03.13.02.S.154-3.S2-ext.SPA.bin I want to upgrade it to isr4300-universalk9.17.12.05a.SPA.binWhen I pass the command ...
Hi, we have one catalyst 8500 router with following os. Cisco IOS XE Software, Version 17.09.05aCisco IOS Software [Cupertino], c8000aes Software (X86_64_LINUX_IOSD-UNIVERSALK9We would like to upgrade it to most stable version. Can anyone please advi...
Hello,I ran into an interesting issue while I was doing an SD-WAN lab. I had 4 routers and a NAT router as the Gateway...The NAT router (CSR1KV not in SD-WAN, this is, in Autonmous mode) is simulating a CGNAT provider that leases the client IPs in th...
Hello,I am working on an automation to have a device moved to a different device template. Before moving it, I need preview the configuration and compare the difference between the existing and new configuration. So I tried searching for a config dif...
Hey,could someone tell me if there is an upgrade path from 17.06.05a to 17.12.06 for C8500L-8S4X or am I able to upgrade driectly to 17.12.06.Also, could someone help where I can find such information? I have searched for about an hour with no succes...
hi team,I have c9300 connected to SRX 340 via static route. I have also VRF on this switch with vrf default route through global. the VRF has source multicast and needs to get out through global routing table. VRF config po11no switchportip vrf for...
A simple topology of three routers R1, R2 and R3 connected in a multiaccess segmetn.R1#sh ip os int f0/0FastEthernet0/0 is up, line protocol is upInternet Address 123.1.1.1/24, Area 0, Attached via Network StatementProcess ID 1, Router ID 1.1.1.1, Ne...
We have a working design with Cisco ASA and Fortiswitch connecting to Cisco ASR1001 router up to AWS. The ASR uses BGP to talk to AWS and we redistribute OSPF/BGP (Which way is right?). At the moment It works and we have traffic flowing. We have intr...
Hello oevery one how to turn on 5 tuple on my nexus 9000? checking here the result,NX9(config)# show ip load-sharingIPv4/IPv6 ECMP load sharing:Universal-id (Random Seed): 782476374Load-share mode : address source-destination port source-destinationG...
Hello,I am running CML 2.8.1 and I cannot get the vManage GUI to work for some reason. I get the following error:I checked that the file is missing:Does anyone know why this happened, and how to fix this?Thanks,Juan
