I have a CISCO887VA-SEC-K9 Router and I want to change it, what equipment do you recommend that is similar?
Forum Posts
Resolved! Cisco Router
Please suggest a router that has at least four RJ45 ports and four SFP ports, and whose end-of-life has not yet been announced.
Resolved! OSPF LFA on Cisco router
Hi everyone,In Juniper, I can configure LFA for link using: " set protocol ospf area 0.0.0.0 interface ge-0/0/1 link-protection.This allow router to pre-compute and install loop free path in forwarding table.Do we have an equivalent functionality on...
I have an ASR920 that can't load from USB0. The output shows... rommon 6 > boot usb0:asr920-universalk9_npe.16.11.01a.SPA.binLocated asr920-universalk9_npe.16.11.01a.SPA.bin, start cluster is 173301#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#.#....
I have the following topology in EVE-NG:My goal is to allow Customer 2 clients (VPC4 and VPC5) to connect to Customer 1's FTP server.ISP router has the following configuration:ISP#show runBuilding configuration...Current configuration : 3520 bytes!! ...
I am looking to update multiple Ip routes that we track in HSRP, but the track statement was missing. If I add the track without removing the already configured route, will it update? Or Do we need to remove the route then re-add it with the track st...
I want to establish a centralized policy in SD-WAN to route traffic to a particular destination FQDN. I understand that in vManage, there are Custom Applications that allow me to define specific FQDNs or applications. However, when attempting to crea...
I have three WANs; one is the primary and the other two are backups. Primary = dhcp; Secondary = Cellular0/2/0; Tertiary = Dialer1The routes are as follows:ip route 0.0.0.0 0.0.0.0 dhcpip route 0.0.0.0 0.0.0.0 Cellular 0/2/0 251ip route 0.0.0.0 0.0.0...
Hi,I would like to confirm if the boost license upto 1.5 Gbps from the data sheet only supports onboard Gigabit Ethernet Interfaces and not Port channels? We have 400 Mbps bandwidth but ISR 4321 only limits it to 200 Mbps. We isolate the issue and it...
Resolved! HSRP
Hi @All I made a demo HSRP lab with the below setup:R1 connected to Switchport E0R2 connected to Switchport E1VPC connected to Switchport E2R1 connected to a tap interface tap1 (192.176.1.1)R2 connected to a tap interface tap2 (168.172.1.1)Conf of R1...
Hello, We have Cisco Meraki MX75 device configured in Meraki Dashboard but not seeing events or logs when we do a API requestcurl --location 'https://n219.meraki.com//api/v1/organizations/{orgId}/appliance/security/events?t1=2024-03-11T24%3A00%3A00Z&...
Hi everyone ,i have faced an issue on ASR 4331 series router as when i am trying shut LAN interface by CLI ,router goes down and we are unable to login that router .after physically rebooting the router, it's back to normal state .can anyone suggest ...
Hi, i hope its right post location for this kind of problem.I tried to send unicast data with PacketSender to Socat(Debian 12 Server), convert that to Multicast and send that data to Cisco multicast interface/group.When i try do send Multicast data w...
What is best way to increase speed and separate two building's networks.Building A has firewall/router which is gateway to internet. DHCP currently DISABLED on this box.about 75 hosts ip addresses in building not all in use at one time.20 port switch...
Resolved! ASR1002X Next Hop SELP IBGP
Hi In ASR1002X in address family on neighbor IP addressany I donnot find next Hop self configuration for ibgp
