Hi guys,Is there a way to source the ping from the standby IP?We have VMware hosts that can't ping the virtual IP address. But they can ping the physical IP addresses on our cores. I just want to try myself to ping their IP from the virtual IP addres...
Hi! This is my first post here. Thanks to Cisco for providing this valuable resource. I'm primarily a Unix system administrator, but I wear many hats do to the small size of the company I'm currently working for. In other words, we don't have a dedic...
I have a 2921 router connected to 2 DSL circuits - DSL1 on gig0/1 and DSL2 on gig0/2.I am using a route map to force individual hosts to use DSL2 for internet traffic. I'm using a standard NAT overload statement with ACL to NAT on both DSL interface...
Cisco 3945 running 15.3(2)T with 1 x EHWIC-1GE-SFP-CU. Configuring the interface as such:conf tint g0/0/0speed 1000duplex fullDoes not yield those settings int the configuration. Is this by design?If this posts answers your question or is helpful,...
Gentlemen,I have a demand for 132 V.35 interfaces, any suggestion about a router which could deal with that?Thanks in advance,Vitor
Hello all!We are building a New Datacenter and extending vlans to this data Center, we route from the core via eigrp to a L3 3750 switch and from there EIGRP to a router for a primary MPLS network using BGP and again to a second, On the router we red...
Hello Need help I have a BOM with a router C2921-VSEC/K9 in my config I put this modulo ISM-VPN-29 can anyone tell me is this is necessary to do VPN IPSEC?can I do that VPN IPsec without that?thanks
I have a Cisco 2811 router and the boot file has been corrupted. I need to replace the firmware to the flash and it says to use the TFTP server. I ran in to some problems.1. The router did not have an ip address set up to it and I am not sure how ...
Hello , I have 2 equipment ONS 15305, 1 of them with STM-1 and another STM-4. What is the replacement of such equipment now, Help to identify the equipment to replace him but other than the ONS 15454 MSTP, I want something cheaper.Thanks you,SFP
Dear All,Please find the below attached Topology:R3,R4 & R5 are directly connected to R1 as a Primary Service Provider to reach the Router R6. All are connected via EBGP and advertising only Loopbacks. So primary path to reach the Loopback of R6 is v...
Dear All....I want to request your advice about E1 internet Line.Now I am preparing cisco 2900 series router to set up E1 internet line.And I will use Hwic 4esw modules card for E1 Line.But Here is problem.The module interface card can't configure IP...
Hola. Tengo una consulta ya que soy nuevo en esto de los routersMe dieron un Router Cisco RV016 y necesito configurarlo y no puedo.Tengo proveedor de Internet Arnet, Usuario, Contraseñia y dos DNS del mismo proveedor, Les cuento lo que hice:Ingreso a...
Hi All,i bought the wrong interface cards vwic3-1mft-e1/t1 and it is not working when my vendor trying to set it up.Need some advise from you guys, if it is possible to configure the e1/t1 card to run on this g703 unframe link? understand the con wil...
Hello.I have configured LDP graceful restart (GR) )on two routers (the same configuration):mpls ldp graceful-restart timers neighbor-liveness 100mpls ldp graceful-restart timers max-recovery 110mpls ldp graceful-restartNext I set TCP filter on both s...
Hello.I have two LSRs connecting via single link. I want to check LDP-OSPF synchronization. But it doesnt work. My config for side A:A#sh run | s ospf router ospf 1 mpls ldp sync mpls ldp autoconfig area 0 log-adjacency-changes network 1.1.1.0 0.0.0....
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM | ||
| 02-04-2026 09:44 PM |
