Hi,I am using iBGP as a routing protocol in a Hub-and-Spoke topology.I configured "bgp redistribute-internal" on the hub router so that all routes learned by SpokeA are forwarded to SpokeB. However, it simply doesn't work. No routes are advertised.I ...
hi all,i'm monitoring a 2951 router for high usage and latency. i've observed rxload is always 255/255.would like to know if this is some kinda cosmetic bug? TIA!2951 uptime is 13 weeks, 6 days, 2 hours, 25 minutesSystem returned to ROM by power-onSy...
I have a client whom uses a DSL 10 MG circuit as their backup circuit for Internet Connectivity in case of a failure. The circuit uses a DSL modem that is unreliable. I was recommending yesterday tot he client that perhaps we could place a Cisco ro...
Hello,We have a new 100mb WAN installed from the UK to Germany and it seems very slow, so I'm after any advise. I've used these iperf commands:Client iperf -c 172.30.0.100 -t 100 -i5 -P 10 -b 11mServeriperf -u -s -i5Results from Uk to Germany PC[ ID...
Hi, I have 2 Routers (2911), 2 ISP Connection, 1 /24 IP Block and AS Number. Indivitually, I did the BGP estbilishment with ISP. Now I trying achieve the load balancing as show in the above figure. 1. Is it possible to split the /24 IP Block into 2 /...
Dear Team,I am using Avaya VPN client & when I am getting connected succesfully to IPSec VPN Server, it is showing in status that IP NAT-Transversal is active on port 10001. In this case my IP is behind the NAPT router. When I am checking the logs, i...
I have downloaded and expanded all the available visios on the http://www.cisco.com/en/US/products/hw/prod_cat_visios.html but there is a lot of outdated material, especially in the routers. I am looking for VWIC3 stencils and the...
Hello CommunityCan someone please show me how install a .lic file onto the new Cisco ISR G2 1921?I know how to install via tftp, however I need to know how to install from USB.Your help will be greatly appreciated.Cheers
Hello Experts,I have a Cisco 2921 series router and Idon't have a CCP to do configuring the firewall, I need your help for the recommended steps of Firewall configuration on the Router and thourgh using CLI.much appreciate your feedback.Hardi
Hi to everyone.I have a question. For example if I configure fair-queue 1000 16 (16 is the number for dynamic queues), what will be with 17th new flow? Because all 16 queues are allocated for existing flows.
Dear support,As per the datasheet of 3850 switch, it states that it includes wireless controller capabilities. can i use the integrated controller as a mobility controller for a small branch (or should i add another 2504 WLC)? kindly advise..Best Reg...
Hidoes a router Cisco 887 va k9 support EIGRP and IPsec ?
hello communityany help much appreciated.Setup as follows:Dual Hub, dynamic bgp discovery for spokes. This works well with hub automatically populating bgp neighbors within the specified range. eBGP between Hubs and spokes.However, I am trying to g...
My 3845 has some loopback interfaces, when I do "show interface", the 5 min input/output rate of them are always "0". If I ping it I can see the packets output, but the 5 min input/output are still 0.is this normal? Thanks,Ryan
Hello together,for testing purposues i wanted to exchange a running ASA 5510 with a ASA 5505.I can't get it working so far and i can't see where the problem is, hopefully there is an expert here, i am kinda new to cisco.I included the running configs...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM | ||
| 02-04-2026 09:44 PM |
