Hi all,I have a doubt.Scenario is:R1 -> R2 -> R3y.y.y.y -> next hop for R2 towards R3R2 learns the network x.x.x.x with a static route towards R1.There is then a BGP session between R2 and R3 and I am announcing the network x.x.x.x to R3.On R2, issui...
Problem Details: I have two switches: Nexus 3064 (ver 5.0(3)U1(2)) and Cisco 6509. The 6509: 1 x WS-x6708-10GE 8 port Ten Gig module version 3.5, firmware 12.2(18r)S1. 2 x sup 720's, with PFC3A. 2 x WS-x6348-rj-45 4 x WS-x6748-ge-tx The IOS is ipser...
We have a customer, who has the following setup:ISP router with ip range: x.x.202.1/ 28That is connected to a Cisco 2960 switch, that doesn't do much but:Vlan5: x.x.202.14 /28Port 1-12 is switchport mode access to vlan 5There are 3 firewall's connect...
I am looking to contain the advertisement and subsequent redistribution of a subnet by use of a ip prifix-list and distribution-list. My question is, Within the specific router eigrp definition of my configuration, if I am redistr...
Hello, I have a paclet flow issue and I know its due to MTU size over ip/vpn. I need to know the optimum size of the MTU size. Check the trace log from the router and let me know ..:HEAD.OFFICE#pingProtocol [ip]:Target IP address: 192.168.188.1R...
Hello, I want to know which of the avaliable Power Supply on the RPS 2300 I must choose for the appropriate working of the basic Router 2911 (without PoE functions):1. 750WAC power supply2. 1150WAC power supplyWhich one of the above PS is the recomme...
Hi All,I would like to know what extactly alarm "system minor alarm on power-supply 1 power-output-mode" mean and how to troubleshoot on it.Please go through the logs attached.Thanks,VB
Hi, I am running VRRP on Cisco 2811 router (Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(15)T1), with another device.i am getting following error message "VRRP: Header ip address count sanity check failed" on Cisco rout...
Hi, a basic question:a) Imagine a router has WIC 2 T1 ports. By default, are those ports OK to receive voice PRIs? Or do I need to install VWIC in order to make such ports process voice PRIs?
I saw the reply to this post: https://supportforums.cisco.com/message/3761251#3761251 and I just wanted to know what the configuration would look like on the ASR. My main purpose for using a bdi interface will be routing [ospf] (almost like router...
Hello every one,what is routing redistribution, for what we use it, why we use it and what it do???i have seen this commandes on EIGRP configuration redistribute connected metric *** *** *** *** **** route-map EIGRP_CONNECTED_OUT redistribute connec...
What am I missing...DEFINE MONITOR PROBE:(config) ip sla monitor <monitor#>(config-sla-monitor)# type [echo] protocol ipicmpecho <target-ip> source-int <int>(config-sla-monitor-echo)# timeout <ms>(config-sla-monitor-echo)# threshold <ms>(config-sla-m...
Folks,Please help me out here. Where does the Inverse ARP run - in the frame-relay switch or in the attached router?Also, when static mapping is configured, does it simply turn off the Inverse ARP or does it just overwrite the dynamic mapping?Thanks
Dear Expert,I would like to ask you regarding creating a route object in RIPE NCC.If i am a transit ISP, i am receiving a prefix from my end user ans advertise it to internet and the customer will be the originator for this prefix.In this case, do i ...
Dear Expert,I would like to ask you regarding creating a route object in RIPE NCC.If i am a transit ISP, i am receiving a prefix from my end user ans advertise it to internet and the customer will be the originator for this prefix.In this case, do i ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-09-2026 09:36 AM | ||
| 03-03-2026 03:16 AM | ||
| 03-01-2026 07:34 PM | ||
| 02-19-2026 05:51 AM | ||
| 02-17-2026 02:51 AM |
