Hello,I have a MPLS L2VPN between two Cisco NCS 5011 routers. Both of the devices are running 7.11.2. When I am trying to pass packets with TTL value 1 (any packets with other TTL values are passing OK), these packets are filtered:show lpts pifib har...
Forum Posts
on Data center router ,we have 6 VRF and let say we have subnet 10.x.x.x/18 and this subnet route is seen in all 6 vrf on that Data center routeris it possible ?as i learnt that VRF creates separate routing table then how can we see one subnet rout...
Resolved! Cisco 1100 ISP Failover
Dear Forum,I'm reaching out for an issue I'm having with a Cisco 1100 running IOS 9.17.09.05. The router is connected to 2 WAN ports with a simple failover config. The primary WAN is on G0/0/0 and the backup is on G0/0/1. When ISP1 (ATT) drops, the d...
This is regarding Cisco SD-WAN using cEdge. Would like to understand, what is the bfd sessions timer value I have configured in my Cisco cEdge devices.Is it seen via show SD-WAN bfd sessions?Basically, I want to understand what is the BFD timers conf...
I have a Zyxel Firewall performing all the routing on my network which includes several VLAN's(VLAN10, 20, etc. I am having a disagreement with the vendor. The only way their device supports VLAN routing you have to set the profile up and map it to a...
I'm having a really difficult time getting TACACS working on a new ASR1001x. I have the device cabled on the management interface and I can ping the TACACS server. Management interface is in the Mgmt-intf VRF. Here is a copy of my config, where am...
I have configured a System IP pool to auto assign system IPs. We also use this as a management address for device access via a loopback configured in a service VPN. Is it possible to reference the auto assigned system IP using a Config Group or CLI...
I want to create an OMP feature configuration that can be used on multiple System Profiles. If I make changes to the OMP feature I want it to update all System Profiles that reference the feature. I see there is a "shared" attribute but I don't kno...
Greetings. Perhaps I'm too green and misunderstanding the situation but I'm not finding a direct answer and my tech leads and support are not available at the moment to clarify this information to me.I was put in charge of monitoring certificates for...
Hello Team,I’ve encountered an issue while setting up an IPSec VPN tunnel between an AWS-hosted Firepower Threat Defense (FTD) firewall (managed by FMC) and an on-site Cisco IR1101 router.In this setup, the FTD is located behind an AWS Network Load B...
Hello I will more generalize my system to get across the idea better. DSL Modem - FPR1010 - SG350XG. All ACL/NAT is done on FPR with a static route to find the 3 VLans on the SG350XG. [FPR 1/2 connects to SG 1/1] On SG I have 3 VLans and each VLan is...
Hi All, I have vmanage version 20.8 in my eveng lab and it was working fine until yesterday. Today when i started the lab, the vmanage GUI is not available. Its says the server is busy. I checked the resource/cpu etc and i have 32GB RAM and 8 vCPU. I...
Hi,Is there any way to get for example, the snmp location of all my sdwan routers with a script?Any API that can help?Regards and thanks
Hi All, Kindly advise if for deploying 8300 (C8300-1N1S-4T2X) as a redundant pair (HA) at internet edge , do we need to interlink the router's direct;y like how we do for core switches or do we just need to make redundant connectivty to wan and inter...
Dear Community,I’m facing an issue with a single-TLOC Cisco SD-WAN branch (Catalyst 8200/8300 on IOS XE 17.15.03, vManage 20.15.03) where the WAN Edge fails to establish BFD Tunnels with other sites even though it can reach the Cisco-hosted Controlle...
