Hello everyone! I am using a topology from Wendell Odom's book: my question is that I am using that topology to simulate the network on packet tracer, but when I issue the command SHOW IP OSPF INTERFACE BRIEF to see the neighbor count, it displays 0...
Hi all, Im having trouble getting my cores to route to my new WLC... I cannot ping the core from the WLC, and cannot ping the wlc from the core. Cores to WLC: 2 interfaces, members of PO71. VLAN allowed statement in use (allowed vlan 271)WLC to Cores...
Hey guys, since my CCNA exams are closing in, I've decided to start putting it all together. Unfortunately, there seems to be an issue for which I need a little help. In the topology (included .pka), I've set up OSPF and NAT translation for both priv...
right now i have mostly everything working, however, one thing we are having issues with is people on our VPN can not connect to a hosted solution.previously they were able to do so and to our knowledge our provider has not done anything to the other...
Hi Support,I need to get System OID of cEdge Router (4431 -4331) version (17.09.04a) and vMange (20.9.4.1) to integrated with Microfocus. Network Node ManagerthanksDalia
A question about VRRP instances/groups and a request for suggestions from the Community.Equipment: Cisco 7609, Cisco NCS-55A2, Cisco Nexus 5596Is VRRP limited to 255 instances? Is there a difference between a VRRP instance and a VRRP group?If there a...
when we attached 500 Mbps internet link to router V1000 then we got to know that V1000 has bandwidth limit of 250 Mbps only .hence 500 Mbps internet link does not work.1.how to check bandwidth limit of router and switch ?is it mentioned in data sheet...
Hello, I was looking at the config on the equipment with vrrp applied, and I saw a config called "timer 200 force" and I need to explain what this means.
Hello,I have recently bought MWR2941 router to my LAB.It had CF card inside but I didn't know how to power it up.I have order 24V 8A power supply and finaly was able to turn it on but...Rommon say it can't boot from flash.I have mwr2941-adviprank9-mz...
Hi eveyone, I might need some help to fix a very wierd issue. I needed to deleate some vlan in a switch, but unfortunately did it on the core. I let you imagine the chaos... now all the vlan are back up, but I have a really wierd case : I have a VM i...
I have a Cisco 800 series router that was previously configured to work with an ISP router in bridge mode. Unfortunately, the person who configured it forgot the password. Following this video tutorial (https://youtu.be/YRGfiHIJ860), I was able to re...
HiI'm curious to know what you think is the best device for shaping traffic, especially when dealing with high volumes like 100G. Would a router be the top choice, or do switches handle this well too?I know that cisco 4500X and Cisco 6816 switches ca...
Hello in our company, we have two C6840-X-LE-40G that are VSS and we want to police traffic on this Switch. I searched and found out that we should use the below command so that the shape works correctly # platform qos police distributed loose/strict...
Hi,I'm sorry to bother you all, but I'm having some issues with the network I'm building in CISCO Packet Tracer.In my network, I need to deny access from one direction but not the other. For instance, in my network, I need the VLAN 20 (172.16.8.0 /24...
R5 R1| (R5 and R4 area 2) | | | (R4 and R3 area 1) | (area 0) |R4- - ---- ------------R3-----------------R2I initiated OSPF with process ID 1 on...
