Hallo, I have the below EEM script configured in C1100 router and I am trying to manually trigger it but it is not working. What could it be that I am doing wrong? event manager applet IP-CHANGEevent noneaction 3.0 cli command "enable"action 4.0 cli ...
Forum Posts
Resolved! I CAN'T PING ALL THE PC AND THE SERVER
Can you help me figured out what's the problem here? Because i can't ping all the pc and the server i configured all the router and all of them is good.
Resolved! How To move NTP From Server to Switch
How to move NTP from server to Switch? how to configure in switch ? ThankYou
Hello Guys!Having issues with intermittent internet services connectivity, and if I change outgoing link (there are two links of different providers) it works for a while but then it starts again.All that I have from logs is this:Nov 2 06:10:02.420: ...
My other other end BGP peer advertises a lot of network, including my side local network. I want my end device to exclude one network from learning (like 192.168.2.0/24). Are there any BGP commands for this.
Resolved! Can't ping
Hello,I'm currently a student and I have some problem and I cant figure this out. I can't make a successful ping from the left side of the subnets to 172.16.100.0/26 subnet(the right one)A packet tracer file is attached in it for you to review.Thanks...
Hello all, A bit of a newbie to the cisco real. I've taken Cisco R&S in college and in the Navy but only getting around to building my first home lab now. I'm having difficulties connecting to the internet from my pc that's hooked up to my switch an...
Resolved! OSPF area ID in IP address format ??
What is the difference between "area1" and "area 0.0.0.1"??I'm not sure how to understand the IP address format of Area.The device is Nexus.
Resolved! EIGRP cannot access internet
Hi there,my topology is ISP-->home wireless wifi-->Cisco (R1)-->Cisco (R2)--> Cisco (R3)3 Cisco router running EIGRP, R1 can access internet, but R2 and R3 cannot access internet.my understanding is redistribute a default network into EIGRP, I tried ...
I've spent the last 24 hours banging my head on getting an IPSec encapsulation to work on my DMVPN Phase 3 GRE tunnels. I have the basic config below for my two routers in play:Hub router: crypto ikev2 keyring DM-KEYRINGpeer ANYaddress 0.0.0.0 0.0.0....
i have a c1111 set up for serving as a vpn server i can connect to it with a desktop and anyconnectto set that up was quiet a hassle for me so i dont want to mess with its settingsi am not at the location and would need access to the local network on...
Hi All, I am unable to stop the traceroute in between on this router. What is the "escape sequence" to get out of traceroute outputs? Ctrl-shift-6 and Ctrl-shift-6 x does not work. Also, the interface names to be case sensitive on this platform. It g...
Resolved! Vlan No Internet
Hi, I have 2 vlans, vlan 1 (default) and vlan 2, each with a separate ethernet connection to a router. hat might sound strange but I'm not trunking today. vlan 1 has an ip of 192.168.1.160 and is connected directly to my home router 192.168.1.1. Th...
HI all, just a question about BGP routing on NX-OS, ISP3 is correctly sending routes to ISP1 and ISP1 is correctly receiving: Now the issue is that all the routes coming from R3-1: *>e10.10.10.0/24 70.70.70.2 0 100 3333 i*>e10.20.20.0/24 70.70.70.2 ...
Hello Everyone. I have a eBGP setup and my iBGP provider is my Datacenter and via iBGP network I get the ISP network.My topology is below: iBGP layer: R2= 173.0.1.1R4= 173.0.2.1R3= 174.0.0.0/28eBGP layer (my side):R1 = ASA-5515X-1: 173.0.1.2R5 = ASA...
