Hello folks.I'm trying to allow end devices to communicate between vlans. I I'm using a Multilayer Switch 3560 24 port. And 4 computers. 2 per vlan. NAME VLAN IP PC10_1 10 10.100.10.50 /24 PC10_2 10 10.100.10.51 /24 PC20_1 20 10.100.20.50 /...
Forum Posts
I want to access two machines having the same IP addresses, I have narrowed the requirement by using VRF and route leaking but am stuck on the natting part, I wanted to do natting within the VRF, where one of the VRF interfaces will act as an outside...
Hi, I have the below topolgy . Now I want to convert area 50. How can I minimize downtime . for example if I am changing switch3 to nssa other ASBR (vios4 ) neighbourship should not go down )The default route injected from the area 0 , If I...
hi,my google search is failing me.just would like to confirm if i can upgrade my NCS 540 from IOS-XR 7.2.2 directly to 7.4.2?what's the difference (pros and cons) using the#install add source /harddisk:/ NCS540-iosxr-k9-7.4.2.tarversus installing/upg...
Hello guys, I have an old switch and a new switch setup and both are connected directly to a core switch. Both old and new switches are set up the same. We'd want to migrate devices that connected to old switch to the new switch. We've moved everythi...
Hey ,I was wondering if there are any debug and show commands for Multicast Service reflection.using Vif interface, so we can check if conversion is happenings or not.
Hi all,I've been working on a lab project and have gotten most of my configuration done but have run into two separate issues on my multi-layer switch that I've been stuck on.The first issue involves OSPF, it works just fine once configured, however,...
Hi, Is there a method or process to Decrypt type 5 password for cisco devices ?? I have seen type 7 decryptor available but not for Type 5. Please suggest if there is any technique. James..!!!
My company uses a single Cisco router at each location. Since routers are used to connect different networks, I'm curious as to why there are many routers at a single location communicating to one another using OSPF.I apologies for the ridiculous qu...
Resolved! OSPF help
Hello everyone, So, I'm having issues with OSPF. I had it working, but after I logged out of the packet tracer, it decided it did not work anymore. It keeps getting stuck in the exstart/dr state. I don't know if this could be a packet tracer issue or...
Hi all!According to cisco, the command redistribute ospf 1 match internal external 1 external 2!--- This redistributes ONLY OSPF External routes, but both type-1 and type-2. only redistribute OE1 and OE2 routes (not O and OIA routes) into BGP, but w...
Hi Team,I want two LAN to communicate with each other which is connected directly to two ports of FW 5506.FW port 1 - 192.168.1.0/24FW port 2 - 192.168.100.0/24Can someone help with the command to achieve communications between LANs. Thankyou
Hi I am trying to do the nat on below topology. I don't know why my client machine is not able to reach to 192.168.200.0 network. My switch can reach out to 192.168.200.0 not sure what is the issue? I have give the IP address to VLAN 1I don't know wh...
Hello,i moved from C897 to ISR 113-8pi created again the Ipsec - flexvpn profile but while i entercrypto ikev2 profile AnyConnect-EAP match identity remote key-id *$AnyConnectClient$*the reouter get only:crypto ikev2 profile AnyConnect-EAP match id...
rommon 2 > bootdevice does not contain a valid magic numberboot: cannot open "flash:"boot: cannot determine first file name on device "flash:"rommon 3 > dir flash:device does not contain a valid magic numberdir: cannot open device "flash:"rommon 4 > ...
